Chattanooga Vectra Neo, Руководство пользователя

Страница: 65 / 86

63
Vectra® Neo Clinical Therapy System
Code
Number Type Message Probable Cause Possible Remedies
100 Information
Attempting to save a treatment to a USB fl ash drive with a blank Patient
ID
Type in or select a Patient ID prior to saving treatment to a USB fl ash drive.
101 Information Attempting to save a Custom protocol with a blank protocol name Ensure protocol name is not blank prior to saving the protocol.
102 Information Attempting to save a Sequence with a blank sequence name Ensure sequence name is not blank prior to saving the sequence.
103 Information Attempting to save the Clinic Name with a blank name Ensure Clinic name is not blank prior to saving the Clinic name.
104 Information Attempting to delete a factory sequence Factory sequences (names begin with a “*”) cannot be deleted.
105 Information Attempting to delete a factory protocol Factory protocols (names begin with a “*”) cannot be deleted.
106 Information
Attempting to save a Custom protocol or Sequence after system memory
has reached the maximum allowed (200)
Delete unused User protocols or sequences.
107
108
109
Information
Information
Information
Attempting to access protocols or sequences and none are found in the
system
1. Custom protocols: No Custom protocols have been saved in the system. Refer to
the CUSTOM PROTOCOLS section on page 59.
2. Sequences: No User sequences have been saved in the system. Refer to the
SEQUENCING OPERATION section on page 50.
110 Information Ultrasound applicator became unplugged during a treatment
Ensure ultrasound applicator is securely connected to the unit prior to starting an
ultrasound treatment.
111 Information No ultrasound applicator is plugged into the unit
Ensure desired ultrasound applicator is securely connected to the unit prior to
selecting an ultrasound treatment.
112 Information
Attempting to select a treatment but available channels for desired
modality are currently in use Complete existing treatment before attempting to start another treatment on the
same channel.
113 Information
Attempting to select an sEMG treatment but sEMG channels are currently
in use Complete existing treatment before attempting to start another treatment on the
same channel.
114 Information
Attempting to select an sEMG treatment but no sEMG is installed on the
Stim 1/2 module.
1. If sEMG is installed on the Stim 1/2 module, reset the Therapy System by turning
the Therapy System Off then back On via the Power button.
2. If sEMG is installed on the Stim 1/2 module and the problem persists, discontinue
use of the device and contact the dealer or factory for technical service.
115 Information
Attempting to select a Laser treatment while another treatment is
running Laser treatments cannot be run concurrently with another treatment. Complete
existing treatment(s) before attempting to select a laser treatment.
116 Information No laser applicator is plugged into the unit
Ensure desired laser applicator is securely connected to the unit prior to selecting a
laser treatment.
117 Information Laser Applicator became unplugged during a laser treatment
Ensure desired laser applicator is securely connected to the unit prior to selecting a
laser treatment.
118 Information Incorrect Laser PIN was entered Enter the correct laser PIN when prompted prior to starting a laser treatment.
119 Information
Attempting to select a laser treatment but no laser module is installed in
the unit
1. If laser module is installed in the unit, ensure module is securely inserted.
2. If laser module is not installed, contact the dealer or factory representative to
purchase one.
120 Information
Attempting to start a Laser treatment but the remote control is not
plugged into the unit Prior to starting a laser treatment, the remote control must be plugged into the unit
and given to the patient to allow use as an emergency stop.
The Vectra® Neo Clinical Therapy System incorporates information, warning, and error messages to inform the user
of problems or potential problems with the system, modality, or accessories.
The numbering sequence is: 100-level
messages are general use information messages, 200-level messages are warnings, and 300-level messages are
errors.
Use the following Troubleshooting Chart to defi ne the code and locate the probable cause and possible remedies
before contacting your dealer or the DJO offi ce.
TROUBLESHOOTING
TROUBLESHOOTING CODES