Chaparral G5312 Скачать руководство пользователя страница 65

Страница: 65 / 160

Monitoring System Status

5-7

CHAN 1

Initiator ID

SCSI ID of
controller on
Channel 1 as set in
the Disk Array
Administrator
software.

Ultra/U2

Hardware runs
as Ultra2.

CHAN 2

Initiator ID

SCSI ID of
controller on
Channel 2 as set in
the Disk Array
Administrator
software.

Ultra/U2

Hardware runs
as Ultra2.

CONTROLLER

Backoff

Percentage set in
Disk Array
Administrator
software. 1% is
default and
recommended
value.

Utility Pri

HIGH, MED, or
LOW utility
priority as set in
Disk Array
Administrator
software.

Alarm Mute

ON or OFF as set
in Disk Array
Administrator
software.

Battery

ENABLED or
DISABLED as
set in Disk Array
Administrator
software.

Cache Lock

ON or OFF as set
in Disk Array
Administrator
software.

Dyn. Spare

ON or OFF as
set in Disk Array
Administrator
software.

CAPI

Version

Version of the
Configuration
Application
Programming
Interface.

Table 5-1. Configuration information (Continued)

Group

Field

What displays

Field

What displays

Содержание G5312

































































































































































Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды

Chaparral G5312, Руководство пользователя

Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды