Chaparral G5312 Скачать руководство пользователя

Страница: 107 / 160

Configuring the Controller

7-27

To upgrade the controller’s firmware:

Call Chaparral technical support for information about downloading the
firmware updates.

See

Chaparral Technical Support

on page 9-1.

From the computer connected to the controller, access the Disk Array
Administrator software.

See Chapter 3,

Accessing the Disk Array Administrator Software

From the System Menu, select

Shutdown/Restart

and press

Enter

The system confirms that you want to shut down.

Select

Yes

and press

Enter

The system confirms that it has shut down.

Press

Enter

to reboot.

While the controller reboots, hold down the space bar on your keyboard.

The Flash Utility screen displays.

Press the number on your keyboard that corresponds to the protocol you want to
use to transfer the firmware upgrade file from your computer to the controller.

We recommend using the KERMIT protocol.

The system shows that it is ready to use KERMIT.

Содержание G5312

































































































































































Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды

Chaparral G5312, Руководство пользователя

Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды