Chaparral G5312 Скачать руководство пользователя

Страница: 39 / 160

Creating and Managing Arrays

4-5

Enter the number of drives (excluding spares) you want in the array and press

Enter

The Select Drives screen displays with a list of all available drives, including
the following information about each drive:

– Channel

– SCSI ID

– Drive capacity

– Drive manufacturer

– Drive model number

– Drive firmware revision

– Drive state

Select the drives you want to use for the array and press

Enter

You select a drive by highlighting it and pressing

Enter

. Each selected drive

turns gray in the drive list. After you press

Enter

for the number of drives you

entered previously, the system automatically goes to the next screen. To skip a
drive, use the

↑

↓

keys.

If the array is mirrored, RAID 3, RAID 4, RAID 5, or RAID 50

and

you have

one or more drives left, the Number of Spares screen displays.

Содержание G5312

































































































































































Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды

Chaparral G5312, Руководство пользователя

Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды