Chaparral G5312 Скачать руководство пользователя страница 66

Страница: 66 / 160

G- and K-Series User’s Guide

5-8

* If you have installed the new optional Fibre Channel interface upgrade, you can also
use the Point-to-Point topology.

To display hardware information only:

From the System Menu, select

Utilities Menu

and press

Enter

The Utilities Menu screen displays.

SEP

Poll Rate

Number of seconds
as set in the Disk
Array
Administrator
software.

Temperature

ON or OFF as
set in Disk Array
Administrator
software.

Slot flags

ON or OFF as set
in Disk Array
Administrator
software.

Global Flags

ON or OFF as
set in Disk Array
Administrator
software.

Table 5-1. Configuration information (Continued)

Group

Field

What displays

Field

What displays

Содержание G5312

































































































































































Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды

Chaparral G5312, Руководство пользователя

Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды