Chaparral G5312 Скачать руководство пользователя

Страница: 15 / 160

Introduction

1-5

Supports full backward compatibility for asynchronous, fast, Ultra 1
(40 MB/sec), and Ultra2 SCSI (80 MB/sec)

Onboard Ultra2 SCSI terminators supporting auto-detection and auto-
configuration for LVD/SE

Onboard termination power source circuit breakers

Note:

There is no support for high-voltage differential (HVD) SCSI (RS-

485 SCSI-3 compliant).

Motherboard Disk Cache (K-Series)

Adaptec AIC-2100 dual-port PCI disk cache ECC memory controller

PCI-to-PCI Bridge providing full CPU and PCI bus concurrency

Disk cache size modularity using standard SDRAM 168-pin ECC DIMM
(16 MB to 128 MB)

Battery backup switching regulator and control interface for controller cache
memory

Onboard battery charger and intelligent control/monitoring interface

Integrated Battery Backup and Interface (K-Series)

Battery charger and battery control interface

Integrated software controlled battery charger, diagnostics, and periodic battery
monitoring

Nickel Metal Hydride (NiMH) battery pack delivery of greater than 72 hours
continuous backup to controller cache memory

Software-controlled battery charger and diagnostics

Содержание G5312

































































































































































Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды

Chaparral G5312, Руководство пользователя

Результаты поиска

Содержание G5312

Отзывы:

Похожие инструкции для G5312

Бренды по названию

Популярные бренды