CD Automation CD3200 Скачать руководство пользователя

Страница: 8 / 50

CD Automation srl

CD3200-1PH from 15A to 110A

User’s Manual

2.2

CD-KP

The CD-KP is designed to be connected with all CD Automation's Thyristor units via RS485

communication. On front unit is possible to read the principal operational parameters of the unit like:

power, tension, current, reference, alarms, etc.

One of these variables can be selected and retransmitted via an isolated output (4÷20mA or 0÷10V)

All the menus (except the operator menu) can be protected by password to avoid accidental change of

configuration parameters by unauthorised personnel.

On front unit is also available a plug-in connector RS485 for connect a PC with the Thyristor units

without open the cabinet and without stop the production process.

Technical Specification:

•

Use in Local/Remote

•

Set Point Ramp UP - Down

•

Scroll selection of:

- Set point

- Power output

- Current

- Voltage

•

Display indication for:

- Heater Break alarm

- SCR short circuit

•

Password for configuration parameters

•

Plug-in connector on front to use software configurator

•

Retransmission (4-20mA or 0-10Vdc) of one of these

parameters: Power PV, Current, Voltage.

•

Dimension 48x96x92mm (LxAxP)

•

Comply with EMC, CE marked

2.3

CD-EASY

CD-EASY is a Memory of support used for maintenance people that is not confident in personal

computer.

With the CD-EASY is possible memorize the configuration of one Thyristor Unit and paste it into another

in few seconds.

CD-EASY could be loaded with the personal configuration of the unit and stored together with the

system drawings in a convenient place, enabling unit reconfiguration within seconds if require.

Содержание CD3200



















































Результаты поиска

Содержание CD3200

Отзывы:

Похожие инструкции для CD3200

Бренды по названию

Популярные бренды

CD Automation CD3200, Руководство пользователя

Результаты поиска

Содержание CD3200

Отзывы:

Похожие инструкции для CD3200

Бренды по названию

Популярные бренды