CD Automation CD3200 Скачать руководство пользователя

Страница: 41 / 50

CD Automation srl

CD3200-1PH from 15A to 110A

User’s Manual

Configuration Parameters

The Configuration Parameters are accessible from the software configurator or through the serial

communication port RS485.

P001L (H01)

Byte Lo = Load Voltage

Function:

This parameter show the Voltage rms value

Min/Max:

0 ÷ 255 (0 ÷ FF Hex)

Value:

Value depends on the Unit type

P001H (H01)

Byte Hi = Load Current

Function:

This parameter shows the Current rms value.

Min/Max:

0 ÷ 255 (0 ÷ FF Hex)

Value:

Value depends on when turns have current transformer and from his size’s.

Example:

With one passage on the current transformer (CT) 25/0.05A, the max value

corresponds to the max value of the CT:

Read value=255 (FF Hex) -> Load Current= 25A

P002L (H02)

Byte Lo = Set-point Voltage

R/W

Function:

This parameter is the Set-point voltage saved by the Calibration Procedure

Min/Max:

0 ÷ 255 (0 ÷ FF Hex)

P002H (H02)

Byte Hi = Set-point Current

R/W

Function:

This parameter is the Set-point of current below which HB alarm occurs

Min/Max:

0 ÷ 255 (0 ÷ FF Hex)

Value:

This value is the load current(P001H) minus % value of parameter P126H

P003 (H03)

Status Table

Function:

It’s a tab in bit that represent the “Status” of thyristor unit

Value:

Bit 0 = 1 -> Short circuit on SCR

Bit 1 = 1 -> Load Failure (HB Alarm)

Bit 2 = 1 -> Output signal ON

Bit 3 = 1 -> HB Calibration in progress

Bit 4 = 1 -> Current Limit Flag

Bit 5 = 1 -> Thermal switch

P004 (H04)

Command Table

R/W

Function:

It’s a tab in bit for remote commands via RS485

Value:

Bit 0 = 1 -> Activate HB Calibration procedure

Bit 1 = 1 -> Input Command from RS485 (see P005)

Bit 2 = 1 -> Disable Output signal (Only with Input from RS485)

Bit 3 = 1 -> Reset HB Alarm

Bit 4 = 1 -> Current Limit via RS485 (see P007)

Note:

When unit is switch off all command parameter are set to 0

P005L (H05)

Input command signal

Function:

This parameter reads the Input command signal (see par. 7.4)

When the P004 Bit1 =1 This parameter could be written and become the Input

Command from RS485

Min/Max:

0 ÷ 255 (0 ÷ FF Hex)

Example:

Input 4mA -> P005L = 0 (0%)

Input 12mA -> P005L = 128 (50%)

Input 20mA -> P005L = 255 (100%)

P005H (H05)

Byte Hi = Ramped Input command signal

Function:

This parameter reads the Input command signal after the ramp

Min/Max:

0 ÷ 255 (0 ÷ FF Hex)

Example:

Input 4mA -> P005H = 0 (0%)

Input 12mA -> P005H = 128 (50%)

Input 20mA -> P005H = 255 (100%)

Содержание CD3200



















































Результаты поиска

Содержание CD3200

Отзывы:

Похожие инструкции для CD3200

Бренды по названию

Популярные бренды

CD Automation CD3200, Руководство пользователя

Результаты поиска

Содержание CD3200

Отзывы:

Похожие инструкции для CD3200

Бренды по названию

Популярные бренды