background image

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

57

2. Remove blower door.
3. All  factory  wires  can  be  left  connected,  but  field  thermostat  and

accessory wiring may need to be disconnected depending on their

length and routing.

4. If  the  vent  and  combustion  air  pipe  passes  through  the  blower

compartment,  it  will  be  necessary  to  remove  the  pipes  from  the

blower compartment.

Disconnect the vent and combustion air pipe by:

a.  Loosen the clamps on the vent couplings and combustion air 

pipe external to the furnace. 

b. Separate the pipes from the couplings and move them aside.

c. Loosen the clamps on the vent couplings and combustion air pipe 

located on the blower shelf.

d. Separate the pipes from the blower compartment and set aside.

e. Remove the couplings from the pipe adapters and set aside.

f. After servicing the blower, reverse steps a through e.

g. Tighten all clamps 15 lb -in.

See 

Fig. 65

 for steps 5 through 14.

5. Remove screws securing blower assembly to blower shelf and slide

blower  assembly  out  of  furnace.  Detach  ground  wire  and

disconnect blower motor harness plugs from blower motor. 

NOTE: 

Blower wheel is fragile. Use care.

6. Clean blower wheel and motor by using a vacuum with soft brush

attachment.  Be  careful  not  to  disturb  balance  weights  (clips)  on

blower wheel vanes. Do not bend wheel or blades as balance will be

affected.

7. If greasy residue is present on blower wheel, remove wheel from

the blower housing and wash it with an appropriate degreaser. To

remove wheel:

a. Mark blower wheel location on shaft before disassembly to 

ensure proper reassembly.

b. Loosen setscrew holding blower wheel on motor shaft. 

NOTE: 

Mark blower mounting arms and blower housing so each arm is

positioned at the same hole location during reassembly.

c. Mark blower wheel orientation and cutoff plate location to 

ensure proper reassembly.

d. Remove screws securing cutoff plate and remove cutoff plate 

from housing.

e. Remove bolts holding motor mounts to blower housing and slide 

motor and mounts out of housing.

f. Remove blower wheel from housing.

g. Clean wheel per instructions on degreaser cleaner. Do not get 

degreaser in motor.

8. Reassemble motor and blower wheel by reversing items 7b through

7f. Ensure wheel is positioned for proper rotation. 

9. Torque motor mounting bolts to 40 +/- 10 lb-in. when reassembling.
10. Torque  blower  wheel  set  screw  to  160  +/-  20  lb-in.  when

reassembling.

11. Verify  that  blower  wheel  is  centered  in  blower  housing  and  set

screw contacts the flat portion of the motor shaft. Loosen set screw

on blower wheel and reposition if necessary.

12. Spin the blower wheel by hand to verify that the wheel does not rub

on the housing.

13. Reinstall blower assembly in furnace.
14. Reinstall 2 screws securing blower assembly to blower deck.
15. Reconnect blower leads to furnace control. Refer to furnace wiring

diagram, and connect thermostat leads if previously disconnected.

NOTE: 

Be  sure  to  attach  ground  wire  and  reconnect  blower  harness

plugs to blower motor.

16. Downflow  or  horizontal  furnaces with  vent  pipe through  furnace

only:

a. Install and connect short piece of vent pipe inside furnace to 

existing vent.

b. Connect vent connector to vent elbow.

17. Turn on electrical supply. Manually close blower door switch. Use a

piece of tape to hold switch closed. Check for proper rotation and

speed changes between heating and cooling by jumpering R to G

and  R  to  Y  on  furnace  control  thermostat  terminals.  If  outdoor

temperature  is  below  70

_

F  (21

_

C),  turn  off  circuit  breaker  to

outdoor  unit  before  running  furnace  in  the  cooling  cycle.  Turn

outdoor  circuit  breaker  on  after  completing  cooling  cycle.  See

Fig. 36

.

NOTE: 

If  R-W/W1  thermostat  terminals  are  jumpered  at  the  time

blower  door  switch  is  closed,  blower  will  run  for  90  sec  before

beginning a heating cycle.

a. Perform component self-test as shown at the bottom of the 

SERVICE label, located on the control door.

b. Verify blower is rotating in the correct direction

18. If  furnace  is  operating  properly,  RELEASE  BLOWER  DOOR

SWITCH.  Remove  any  jumpers  or  reconnect  any  disconnected

thermostat leads. Replace blower door.

19. Turn on gas supply and cycle furnace through one complete heating

cycle. Verify the furnace temperature rise as shown in Adjustments

Section. Adjust temperature rise as shown in Adjustments Section. 

A11584

Fig. 65 – Blower Assembly

WARNING

!

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury or death.

Blower  door  switch  opens  115-v  power  to  control.  No  component

operation  can  occur  unless  switch  is  closed.  Caution  must  be  taken

when manually closing this switch for service purposes.

SET SCREW

MOTOR WHEEL HUB

MOTOR SHAFT FLAT

SCREW

MOTOR ARM

GROMMET

SCREW LOCATION

BLOWER HSG ASSY

BRACKET

BRACKET
ENGAGEMENT

SEE DETAIL 

A

CAPACITOR
OR POWER CHOKE
(WHEN USED)

BRACKET

SCREW 

(GND)

BLOWER HSG ASSY

MOTOR, BLOWER

WHEEL, BLOWER

CUTOFF, BLOWER

DETAIL 

A

Содержание N92ESN



































































Отзывы: