Carrier N92ESN Скачать руководство пользователя

Страница: 6 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A93044

Fig. 5 – Installation in a Garage

CODES AND STANDARDS

Follow all national and local codes and standards in addition to these

instructions. The installation must comply with regulations of the

serving gas supplier, local building, heating, plumbing, and other codes.

In absence of local codes, the installation must comply with the national

codes listed below and all authorities having jurisdiction.
In the United States and Canada, follow all codes and standards for the

following:

Safety

• US: Current edition of National Fuel Gas Code (NFGC) NFPA

54/ANSI Z223.1 and the Installation Standards, Warm Air Heating

and Air Conditioning Systems ANSI/NFPA 90B

• A manufactured (Mobile) home installation must conform with the

Manufactured Home Construction and Safety Standard, Title 24 CFR,

Part 3280, or when this standard is not applicable, the Standard for

Manufactured Home Installation (Manufactured Home Sites,

Communities, and Set-Ups), ANSI/NCS A225.1, and/or

CAN/CSA-Z240, MH Series Mobile Homes

• CANADA: Current edition of National Standard of Canada, Natural

Gas and Propane Installation Code (NSCNGPIC) CAN/CSA B149.1

General Installation

• US: NFGC and the NFPA 90B. For copies, contact the National Fire

Protection Association Inc., Batterymarch Park, Quincy, MA 02269;

or for only the NFGC contact the American Gas Association, 400 N.

Capitol, N.W., Washington DC 20001

• CANADA: NSCNGPIC. For a copy, contact Standard Sales, CSA

International, 178 Rexdale Boulevard, Etobicoke (Toronto), Ontario,

M9W 1R3, Canada

Combustion and Ventilation Air

• US: Section 9.3 of the current edition of NFPA 54/ANSI Z223.1 Air

for Combustion and Ventilation

• CANADA: Part 8 of the current edition of CAN/CSA B149.1, Venting

Systems and Air Supply for Appliances

Duct Systems

• US and CANADA: Current edition of Air Conditioning Contractors

Association (ACCA) Manual D, Sheet Metal and Air Conditioning

Contractors National Association (SMACNA), or American Society

of Heating, Refrigeration, and Air Conditioning Engineers

(ASHRAE) Fundamentals Handbook Chapter 35

Acoustical Lining and Fibrous Glass Duct

• US and CANADA: Current edition of SMACNA, NFPA 90B as tested

by UL Standard 181 for Class I Rigid Air Ducts

Gas Piping and Gas Pipe Pressure Testing

• US: Current edition of NFPA 54/ANSI Z223.1 NFGC; Chapters 5, 6,

7, and 8 and national plumbing codes.

CANADA: Current edition of CAN/CSA-B149.1, Parts 4, 5, 6, and 9.

In the state of Massachusetts:

• This product must be installed by a licensed plumber or gas fitter.

• When flexible connectors are used, the maximum length shall not

exceed 36 in. (914 mm).

• When lever type gas shutoffs are used they shall be T-handle type.

• The use of copper tubing for gas piping is not approved by the state of

Massachusetts.

Electrical Connections

• US: Current edition of National Electrical Code (NEC) NFPA 70

• CANADA: Canadian Electrical Code CSA C22.1

Condensate Drain Connection

• US: Current edition of National Standard Plumbing Code, Section 8.7.

• Canada: Current edition of National Plumbing Code of Canada in

Canada.

ELECTROSTATIC DISCHARGE (ESD)

PRECAUTIONS PROCEDURE

1. Disconnect all power to the furnace. Multiple disconnects may be

required. DO NOT TOUCH THE CONTROL OR ANY WIRE

CONNECTED TO THE CONTROL PRIOR TO DISCHARGING

YOUR BODY’S ELECTROSTATIC CHARGE TO GROUND.

2. Firmly touch the clean, unpainted, metal surface of the furnace

chassis which is close to the control. Tools held in a person’s hand

during grounding will be satisfactorily discharged.

3. After touching the chassis, you may proceed to service the control

or connecting wires as long as you do nothing to recharge your

body with static electricity (for example; DO NOT move or shuffle

your feet, do not touch ungrounded objects, etc.).

4. If you touch ungrounded objects (and recharge your body with

static electricity), firmly touch a clean, unpainted metal surface of

the furnace again before touching control or wires.

5. Use this procedure for installed and uninstalled (ungrounded)

furnaces.

WARNING

FIRE, INJURY OR DEATH HAZARD

Failure to follow this warning could result in personal injury, death

and/or property damage.

When the furnace is installed in a residential garage, the burners and

burner ignition devices must be located at least 18 in. (457 mm) above

the floor. The furnace must be located or protected to avoid damage by

vehicles. When the furnace is installed in a public garage, airplane

hangar, or other building having a hazardous atmosphere, the furnace

must be installed in accordance with the current edition of NFPA

54/ANSI Z223.1 or CAN/CSA B149.2. See

Fig. 5

18-IN. (457.2 mm)

MINIMUM TO BURNERS

CAUTION

FURNACE RELIABILITY HAZARD

Failure to follow this caution may result in unit component damage.
Electrostatic discharge can affect electronic components. Take

precautions during furnace installation and servicing to protect the

furnace electronic control. Precautions will prevent electrostatic

discharges from personnel and hand tools which are held during the

procedure. These precautions will help to avoid exposing the control to

electrostatic discharge by putting the furnace, the control, and the

person at the same electrostatic potential.

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды