Carrier N92ESN Скачать руководство пользователя

Страница: 18 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A10491

Fig. 25 – Installation on Combustible Flooring

Filter Arrangement

There are no provisions for an internal filter in these furnaces. An

external filter rack is required and is purchased separately. A field

supplied accessory air cleaner may also be used in place of the filter

rack.
For upflow applications, the filter can be installed on either side of the

furnace, the bottom of the furnace or any combination of side and

bottom of the furnace. (See

Fig. 21

)

For downflow applications, the filter rack (or field supplied accessory air

cleaner) must only be connected to the bottom opening on the furnace

(See

Fig. 22

For horizontal applications, the filter rack (or field supplied accessory air

cleaner) can be connected to the bottom opening on the furnace. For side

return use in the horizontal position, refer to

Fig. 23

. If both side and

bottom openings are used in

Fig. 23

each opening used will require a

filter.
A filter rack or any field supplied accessory air cleaner can also be

installed in the common return duct prior to entering the return air

opening in any orientation.
Refer to the instructions supplied with the Filter Rack or accessory air

filter for assembly and other details.

Due to the relatively high pressure drops of 1-in (25 mm) thick

after-market filter media, it is recommended that the filtration system be

designed for at least 2-in (51 mm) thick media.

Filter and Return Duct Sizing

Pressure drop must be taken into account when sizing filters, filter racks,

IAQ devices, and associated system ductwork. See

Table 6

for a

comparison of Pressure Drop (initial/clean resistance to airflow) versus

Airflow for a variety of filter media types and sizes. These are

representative numbers. Consult the filter or IAQ device manufacturers’

specification sheet for performance data for a particular filter media or

IAQ device.
Design the filter and associated ductwork for the best match of pressure

drop versus filter size. Best practice usually chooses filter systems with

pressure drops under 0.2 in. W.C. (50 Pa), with the best blower electrical

efficiency and system airflow performance occurring with filter pressure

drops under 0.1 in. W.C. (25 Pa).

Provide duct transitions, as required, to smoothly transition airflow from

the return duct system to the filter (or IAQ device) to the furnace when

the dimensions of the ductwork or furnace return air opening do not

match the required filter or IAQ device dimensions. See the instructions

supplied with factory-accessory duct adapters.

(533)

Upflow Applications on Combustible or Noncombustible Flooring

(Subbase not required)

19-1/2

(495)

21-5/8

(549)

20-1/8

(511)

22-1/4

(565)

Downflow Applications on Noncombustible Flooring

(Subbase not required)

19-3/8

(492)

(483)

(508)

19-5/8

(498)

Downflow applications on combustible flooring

(Subbase required)

18-5/8

(473)

(483)

20-1/4

(514)

20-5/8

(600)

Downflow Applications on Combustible Flooring with coil assembly

coil or coil box (Subbase not required)

(483)

(508)

24-1/2

(622)

Upflow Applications on Combustible or Noncombustible Flooring

(Subbase not required)

(584)

21-1/8

(537)

23-5/8

(600)

22-1/4

(565)

Downflow Applications on Noncombustible Flooring

(Subbase not required)

22-7/8

(581)

(483)

23-1/2

(597)

19-5/8

(498)

Downflow applications on Combustible flooring

(Subbase required)

22-1/8

(562)

(483)

23-3/4

(603)

20-5/8

(600)

Downflow Applications on Combustible Flooring with coil assembly

coil or coil box (Subbase not required)

22-1/2

(572)

(483)

23-1/2

(597)

(508)

*. Not all families have these models

Table 5 – Opening Dimensions - In. (mm) (Continued)

FURNACE

CASING WIDTH

IN. (mm)

APPLICATION

PLENUM OPENING

FLOOR OPENING

WARNING

FIRE, CARBON MONOXIDE AND POISONING

HAZARD

Failure to follow this warning could result in fire, personal injury or

death.

Never operate a furnace without a filter or filtration device installed.

Never operate a furnace with filter or filtration device access doors

removed.

PLENUM

OPENING

FLOOR

OPENING

DOWNFLOW

SUBBASE

SHEET METAL

PLENUM

FLOOR

OPENING

FURNACE

(OR COIL CASING

WHEN USED)

COMBUSTIBLE

FLOORING

APPROVED

COIL ASSEMBLY

COIL BOX

FURNACE

SHEET METAL

PLENUM

FLOOR

OPENING

COMBUSTIBLE

FLOORING

NOTICE

Design the duct system FIRST to determine how much pressure drop

may be allowed in the filter system. See the Air Ducts section.

Excessive filter pressure drop often compromises system airflow and

duct performance, causes inadequate airflow to the furthest ends of the

duct system, as well as causes excess noise and higher than anticipated

electrical consumption.

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды