Carrier N92ESN Скачать руководство пользователя страница 32

Страница: 32 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Locating the Vent Termination

General

NOTE:

Termination Requirements for the Provinces of Alberta and

Saskatchewan are located at the end of this section.
Combustion-air inlet pipe (direct vent/2-pipe system only) and vent pipe

must terminate outside structure, either through sidewall or roof.
Special termination requirements may be required in other Canadian

provinces. Refer to the authority having jurisdiction for clarification

and/or additional clearance requirements.
For vent termination clearance, references to National codes are shown

Fig. 46

for Direct Vent/2-Pipe system and

Fig. 47

for Ventilated

Combustion Air/Non-direct Vent/1-Pipe system. For exterior

termination arrangements, refer to

Fig. 39

for Direct Vent/2-Pipe system

and

Fig. 40

for Ventilated Combustion Air/Non-Direct/1-Pipe system.

Contact Local code authorities for other requirements to and/or

exemptions from the National codes shown in the figures.
Roof termination is the recommended termination location. Roof

terminations provide better performance against sustained prevailing

winds. The roof location is preferred since the vent and combustion air

system is less susceptible to damage or contamination. The termination

is usually located away from adjacent structures or other obstacles such

as inside corners, windows, doors or other appliances. It is less prone to

icing conditions, and it often has less visible vent vapors.
Sidewall terminations may require sealing or shielding of building

surfaces with a corrosive resistance material due to the corrosive

properties of combustion products from the vent system, as well as

protection of adjacent structures.

When determining appropriate location for termination, consider the

following guidelines:

1. Comply with all clearance requirements stated in

Fig. 46

Fig. 47

per application.

2. The vent termination must be located at least 3 feet from an inside

corner and follow the clearance distances in the Inside Corner

Termination drawing. See

Fig. 42

3. Termination or termination kit should be positioned where vent

vapors will not damage plants/shrubs, air conditioning equipment

or utility meters.

4. Do not locate termination directly into prevailing winds.

Termination should be positioned so that it will not be affected by

sustained prevailing winds over 30 mph, wind eddy, such as inside

building corners, or by recirculation of flue gases, airborne leaves,

or light snow.

5. Termination or termination kit should be positioned where it will

not be damaged by or subjected to foreign objects such as stones,

balls, etc.

6. Termination or termination kit should be positioned where vent

vapors are not objectionable

Direct Vent / 2-Pipe System

Direct vent (2-pipe) vent and combustion air pipes must terminate

outside the structure. See

Fig. 46

For references to vent clearances

required by National code authorities. Allowable vent and combustion

air terminations are shown in

Fig. 39

A12220

Fig. 41 – Sample Inlet Air Pipe Connection for Polypropylene

Venting Systems

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the instructions outlined below for each appliance

being placed into operation could result in carbon monoxide poisoning

or death.

The instructions included with this furnace

DO NOT APPLY

to vent

systems that are located below the furnace.

CAREFULLY FOLLOW

THE INSTRUCTIONS PROVIDED WITH THE EXTERNAL

VENT TRAP KIT FOR LAYING OUT THE VENTING SYSTEM

AND THE DRAIN SYSTEM

when all or part of the venting system is

placed below the furnace.

Proper configuration of the venting and drain system is critical when

placing all or part of the venting system below the level of the furnace.

VENT GASSES COULD BE RELEASED FROM THE

DRAINAGE SYSTEM

if the instructions provided with the External

Vent Trap Kit are not followed.

NOTICE

RECOMMENDED SUPPORT FOR VENT

TERMINATIONS

It is recommended that sidewall vent terminations in excess of 24

inches (0.6 M) or rooftop terminations in excess of 36 inches (1 M) in

vertical length be supported by

EITHER

the Direct Vent Termination

Kit shown in

Table

or by field-supplied brackets or supports fastened

to the structure.

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the instructions outlined below for each appliance

being placed into operation could result in carbon monoxide poisoning

or death.

For all venting configurations for this appliance and other gas

appliances placed into operation for the structure, provisions for

adequate combustion, ventilation, and dilution air must be provided in

accordance with:

U.S.A. Installations

: Section 9.3 of current edition of NFPA 54/ANSI

Z223.1 Air for Combustion and Ventilation and applicable provisions

of the local building codes.

Canadian Installations

: Part 8 of current edition of

CAN/CSA-B149.1. Venting Systems and Air Supply for Appliances

and all authorities having jurisdiction.

EXAMPLE FOR

UPFLOW INSTALLATIONS.

MAY BE APPLIED TO

OTHER CONFIGURATIONS.

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды