Carrier N92ESN Скачать руководство пользователя

Страница: 9 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Table 4 – Minimum Space Volumes for 100% Combustion, Ventilation and Dilution Air from Outdoors

NP = Not Permitted

L12F012

Fig. 6 – Air for Combustion, Ventilation, and Dilution for Outdoors

Outdoor Combustion Air Method

1. Provide the space with sufficient air for proper combustion,

ventilation, and dilution of flue gases using permanent horizontal or

vertical duct(s) or opening(s) directly communicating with the

outdoors or spaces that freely communicate with the outdoors.

Fig. 6

illustrates how to provide TWO OUTDOOR OPENINGS,

one inlet and one outlet combustion and ventilation air opening, to

the outdoors.

a. One opening MUST commence within 12 in. (300 mm) of the

ceiling and the second opening MUST commence within 12 in.

(300 mm) of the floor.

b. Size openings and ducts per

Fig. 6

and

Table 3

c. TWO HORIZONTAL DUCTS require 1 sq. in. (645 sq. mm) of

free area per 2,000 BTUh (1,100 mm2/kW) of combined input

for all gas appliances in the space per

Fig. 6

and

Table 3

d. TWO OPENINGS OR VERTICAL DUCTS require 1 sq. in.

(645 sq. mm) of free area per 4,000 BTUh (550 mm2/kW) for

combined input of all gas appliances in the space per

Fig. 6

and

Table 3

L12F013

Fig. 7 – Air for Combustion, Ventilation, and Dilution from Indoors

3. ONE OUTDOOR OPENING requires:

a. 1 sq. in. (645 sq. mm) of free area per 3,000 BTUh (734

mm2/kW) for combined input of all gas appliances in the space

per

Fig. 6

and

Table 3

b. Not less than the sum of the areas of all vent connectors in the

space.

The opening shall commence within 12 in. (300 mm) of the ceiling.

Appliances in the space shall have clearances of at least 1 in. (25 mm)

from the sides and back and 6 in. (150 mm) from the front. The opening

shall directly communicate with the outdoors or shall communicate

through a vertical or horizontal duct to the outdoors or spaces (crawl or

attic) that freely communicate with the outdoors.

Indoor Combustion Air NFPA & AGA

Standard and Known-Air-Infiltration Rate Methods

Indoor air is permitted for combustion, ventilation, and dilution, if the

Standard or Known-Air-Infiltration Method is used.

OTHER THAN FAN-ASSISTED TOTAL

(1,000’S BTUH GAS INPUT RATE)

FAN-ASSISTED TOTAL

(1,000’S BTUH GAS INPUT RATE)

ACH

100

120

Space Volume Ft

)

0.60

1,050 (29.7)

1,400 (39.6)

1,750

(49.5)

1,400 (39.6)

1,500 (42.5)

2,000 (56.6)

2,500 (70.8)

3,000 (84.9)

0.50

1,260 (35.6)

1,680 (47.5)

2,100

(59.4)

1,680 (47.5)

1,800 (51.0)

2,400 (67.9)

3,000 (84.9)

3,600 (101.9)

0.40

1,575 (44.5)

2,100 (59.4)

2,625

(74.3)

2,100 (59.4)

2,250 (63.7)

3,000 (84.9)

3,750 (106.1)

4,500 (127.3)

0.30

2,100 (59.4)

2,800 (79.2)

3,500

(99.1)

2,800 (79.2)

3,000 (84.9)

4,000 (113.2)

5,000 (141.5)

6,000 (169.8)

0.20

3,150 (89.1)

4,200 (118.9)

5,250

(148.6)

4,200 (118.9)

4,500 (127.3)

6,000 (169.8)

7,500 (212.2)

9,000 (254.6)

0.10

6,300 (178.0)

8,400 (237.8)

10,500

(297.3)

8,400 (237.8)

9,000 (254.6) 12,000 (339.5) 15,000 (424.4) 18,000 (509.2)

0.00

*Minimum dimensions of 3‐in. (76mm)

NOTE

: Use any of the following combinations of openings:

A & B, C & D, D & E, F & G

* Minimum opening size is 100 sq in. (64516 sq. mm) with

minimum dimensions of 3‐in. (76mm)

{

Minimum of 3‐in. (76mm) when type‐B1 vent is used.

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды