background image

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

37

A13078A

Fig. 48 – Alberta and Saskatchewan Vent Termination

A93034

Fig. 49 – Combustion Air and Vent Pipe Diameter Transition 

Location and Elbow Configuration

Recommended Combustion Air Inlet Moisture Trap

Recommended  to  prevent  moisture  from  trickling  into  the  furnace

vestibule, a trap can be installed in the intake air pipe near the furnace.

To prevent moisture, connecting a drain line to the trap is recommended

as trace amounts of moisture will evaporate into the intake air stream. If

the combustion air inlet is located near a moisture exhaust duct, or there

are  other  concerns  of  excessive  moisture  being  drawn  into  the

combustion air inlet, it is encouraged to connect a drain line to the trap. 
The trap can be constructed from a running tee of the same diameter of

the intake air pipe with 

EITHER 

a removable cap attached to a 6-inch

long  pipe  connected  to  the  tee  or  the  External Vent  Trap  Kit  to  help

prevent contaminants from entering the furnace. See 

Fig. 50

. 

The  External Vent  Trap  Kit  accessory  may  be  used  as  a  trap  for  the

combustion air inlet pipe if a large amount of moisture must be removed.

The  drain  line  may  be  connected  to  the  same  drain  as  the  furnace

condensate and the evaporator coil condensate line 

ONLY 

if the inlet air

trap drain and the evaporator coil drain empty into an open segment of

pipe above the drain. See 

Fig. 12

. When using the External Vent Trap

Kit, refer to those instructions for proper drain connections.
The tee may also be connected to the intake air pipe on the side of the

casing. See 

Fig. 50

. 

In any configuration, it will be necessary to add the equivalent length of

the tee (15 feet/5 M) to the Total Equivalent Vent Length of the venting

system.

The measured length of pipe used in a single or 2-pipe termination is

included in the total vent length. Include deductions from the Maximum

Equivalent  Vent  Length  (MEVL)  contained  in  the  Venting  Tables  for

elbows  and  flexible  vent  pipe.  Factory  accessory  concentric  vent

terminations  or  pipe  lengths  and  elbows  used  for  “standard”  vent

terminations do not require a deduction from the Maximum Equivalent

Vent  Length.  See  vent  termination  figures  associated  with 

Table 13

.

NOTICE

!

OPTIONAL CONFIGURATION FOR COMBUSTION 

AIR INLET PIPE

In applications where there is a risk of excessive moisture entering the

combustion air inlet pipe, a moisture trap may be added to the inlet pipe

to help prevent moisture from entering the furnace from the combustion

air inlet pipe. See 

Fig. 50

.

When  sizing  venting  systems,  the  equivalent  length  of  the  optional

moisture trap (15 feet/5 M) must be taken into account.

OPTIONAL TERMINATION
BRACKET FOR 2-PIPE
TERMINATIONS

12-IN. (305 MM)

ABOVE ANTICIPATED 

SNOW LEVEL

12 IN. (305 MM) MIN. 
SEPARATION BETWEEN 
BOTTOM OF COMBUSTION 
AIR AND BOTTOM OF VENT.

12 IN. (305 MM) MIN. SEPARATION
BETWEEN BOTTOM OF
COMBUSTION AIR AND
BOTTOM OF VENT.

MAINTAIN 12 IN. (305 MM)
CLEARANCE ABOVE
HIGHEST ANTICIPATED
SNOW LEVEL OR GRADE,
WHICHEVER IS GREATER.

COMBUSTION-AIR

(ELBOW PARALLEL TO WALL)

OPTIONAL
BRACKET 
COUPLING

OVERHANG

12 IN. (305 MM) MIN. GROUND
LEVEL OR ANTICIPATED SNOW LEVEL

EXHAUST

CLEARANCE TO OVERHANG PER CODE

NOTICE

!

ADDITIONAL INFORMATION FOR POLYPROPYLENE 

VENTING SYSTEMS

Polypropylene  venting  systems  include  flexible  vent  pipe.  These

flexible vent pipes have a different equivalent vent length than straight

sections of PVC/ABS DWV vent pipe. Be sure to make the appropriate

deductions  from  the  Maximum  Equivalent  Vent  Length  (MEVL),  or

additions to the Total Equivalent Vent Length (TEVL), when applying

flexible  vent  pipes  in  polypropylene  venting  systems.  See  the

polypropylene vent system manufacturer’s installation instructions for

details.

When using metric-sized venting systems, use these equivalencies for

obtaining the proper MEVL from the Tables:

Use 2” Vent Tables for 60 mm (o.d.) vent systems

Use 3” Vent Tables for 80 mm (o.d.) vent systems

Use 4” Vent Tables for 100 mm (o.d.) vent systems

FURNACE

PIPE DIAMETER

TRANSITION IN

VERTICAL SECTION

NOT IN
HORIZONTAL
SECTION

Содержание N92ESN



































































Отзывы: