Carrier N92ESN Скачать руководство пользователя

Страница: 38 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Include a deduction for a Tee when used for Alberta and Saskatchewan

terminations.

NOTE:

Polypropylene venting systems MAY require additional

deductions from the MEVL, or additions to the TEVL, for vent

terminations and flexible pipe sections. See the polypropylene venting

system manufacturer’s instructions for details on equivalent lengths of

vent terminations and flexible vent pipes, and for calculating total vent

lengths.
To calculate the Total Equivalent Vent Length (TEVL) of the venting

system:

1. Measure the individual distance from the furnace to the termination

for each pipe.

2. Count the number of elbows for each pipe.
3. For each pipe, multiply the number of elbows by the equivalent

length for the type of elbow used. Record the equivalent length of

all the elbows for each pipe.

4. If a Tee is used on the termination (Alberta and Saskatchewan,

when required) record the equivalent length of the Tee used.

5. Calculate Total Equivalent Vent Length by adding the equivalent

lengths of the fittings to the lengths of the individual vent and

combustion air pipes.

A170122A

Fig. 50 – Recommended Combustion Air Inlet Moisture Trap

6. When using polypropylene venting systems with flexible vent

pipes, perform adjustments for the equivalent length of the flexible

vent pipe to the calculated total equivalent venting system length.

See the polypropylene vent system manufacturer’s instructions for

details.

7. Select a diameter of vent pipe from

Table 13

and note the

Maximum Equivalent Vent Length (MEVL) shown for that

application for that specific furnace input size. Compare the Total

Equivalent Vent Length (TEVL) to the MEVL:

8. If the Total Equivalent Vent Length is

shorter

than the Maximum

Equivalent Vent Length for the diameter of pipe chosen, then that

diameter of pipe selected may be used.

9. If the Total Vent Length is

longer

than the Maximum Equivalent

Vent Length for the diameter of pipe chosen, that diameter pipe

MAY NOT be used for venting the furnace. Try the next larger

diameter pipe

NOTE:

If the calculated Total Equivalent Vent Lengths results in

different diameter pipes for the vent and combustion air, select the larger

diameter for both pipes.

NOTE:

If the Maximum Vent Length for diameter of the pipe selected is

longer than the measured length and the equivalent length of all the

fittings and terminations (TEVL), recalculate Total Equivalent Vent

Length using the next smaller diameter. If the Maximum Equivalent

Vent Length is still longer than the longer TEVL of the vent pipe or

combustion air pipe, then that diameter of pipe selected may be used.
When installing vent systems pipe lengths of 10 ft. (3 M) or less, use the

smallest allowable pipe diameter. Using a pipe size greater than required

for short venting systems may result in loss of efficiency, incomplete

combustion, flame disturbance, or flame sense lockout.
For vent systems longer than 10 ft. (3 M), any larger diameter vent pipe

shown in

Table 13

FOR THAT SIZE FURNACE

may be used.

Representative drawing only, some models may vary in appearance.

TO CODE--APPROVED DRAIN OR CONDENSATE PUMP

Tee

Dry Well

Cap

(water tight

and removable)

Tee

Dry Well

Cap

(water tight

and removable)

Tee

Dry Well

Cap

(water tight

and removable)

Recommend “T” fitting with 4--inch minimum height standpipe (

) of same diameter or larger extending upward.

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды