Carrier N92ESN Скачать руководство пользователя

Страница: 57 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

2. Remove blower door.
3. All factory wires can be left connected, but field thermostat and

accessory wiring may need to be disconnected depending on their

length and routing.

4. If the vent and combustion air pipe passes through the blower

compartment, it will be necessary to remove the pipes from the

blower compartment.

Disconnect the vent and combustion air pipe by:

a. Loosen the clamps on the vent couplings and combustion air

pipe external to the furnace.

b. Separate the pipes from the couplings and move them aside.

c. Loosen the clamps on the vent couplings and combustion air pipe

located on the blower shelf.

d. Separate the pipes from the blower compartment and set aside.

e. Remove the couplings from the pipe adapters and set aside.

f. After servicing the blower, reverse steps a through e.

g. Tighten all clamps 15 lb -in.

See

Fig. 65

for steps 5 through 14.

5. Remove screws securing blower assembly to blower shelf and slide

blower assembly out of furnace. Detach ground wire and

disconnect blower motor harness plugs from blower motor.

NOTE:

Blower wheel is fragile. Use care.

6. Clean blower wheel and motor by using a vacuum with soft brush

attachment. Be careful not to disturb balance weights (clips) on

blower wheel vanes. Do not bend wheel or blades as balance will be

affected.

7. If greasy residue is present on blower wheel, remove wheel from

the blower housing and wash it with an appropriate degreaser. To

remove wheel:

a. Mark blower wheel location on shaft before disassembly to

ensure proper reassembly.

b. Loosen setscrew holding blower wheel on motor shaft.

NOTE:

Mark blower mounting arms and blower housing so each arm is

positioned at the same hole location during reassembly.

c. Mark blower wheel orientation and cutoff plate location to

ensure proper reassembly.

d. Remove screws securing cutoff plate and remove cutoff plate

from housing.

e. Remove bolts holding motor mounts to blower housing and slide

motor and mounts out of housing.

f. Remove blower wheel from housing.

g. Clean wheel per instructions on degreaser cleaner. Do not get

degreaser in motor.

8. Reassemble motor and blower wheel by reversing items 7b through

7f. Ensure wheel is positioned for proper rotation.

9. Torque motor mounting bolts to 40 +/- 10 lb-in. when reassembling.
10. Torque blower wheel set screw to 160 +/- 20 lb-in. when

reassembling.

11. Verify that blower wheel is centered in blower housing and set

screw contacts the flat portion of the motor shaft. Loosen set screw

on blower wheel and reposition if necessary.

12. Spin the blower wheel by hand to verify that the wheel does not rub

on the housing.

13. Reinstall blower assembly in furnace.
14. Reinstall 2 screws securing blower assembly to blower deck.
15. Reconnect blower leads to furnace control. Refer to furnace wiring

diagram, and connect thermostat leads if previously disconnected.

NOTE:

Be sure to attach ground wire and reconnect blower harness

plugs to blower motor.

16. Downflow or horizontal furnaces with vent pipe through furnace

only:

a. Install and connect short piece of vent pipe inside furnace to

existing vent.

b. Connect vent connector to vent elbow.

17. Turn on electrical supply. Manually close blower door switch. Use a

piece of tape to hold switch closed. Check for proper rotation and

speed changes between heating and cooling by jumpering R to G

and R to Y on furnace control thermostat terminals. If outdoor

temperature is below 70

F (21

C), turn off circuit breaker to

outdoor unit before running furnace in the cooling cycle. Turn

outdoor circuit breaker on after completing cooling cycle. See

Fig. 36

NOTE:

If R-W/W1 thermostat terminals are jumpered at the time

blower door switch is closed, blower will run for 90 sec before

beginning a heating cycle.

a. Perform component self-test as shown at the bottom of the

SERVICE label, located on the control door.

b. Verify blower is rotating in the correct direction

18. If furnace is operating properly, RELEASE BLOWER DOOR

SWITCH. Remove any jumpers or reconnect any disconnected

thermostat leads. Replace blower door.

19. Turn on gas supply and cycle furnace through one complete heating

cycle. Verify the furnace temperature rise as shown in Adjustments

Section. Adjust temperature rise as shown in Adjustments Section.

A11584

Fig. 65 – Blower Assembly

WARNING

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury or death.

Blower door switch opens 115-v power to control. No component

operation can occur unless switch is closed. Caution must be taken

when manually closing this switch for service purposes.

SET SCREW

MOTOR WHEEL HUB

MOTOR SHAFT FLAT

SCREW

MOTOR ARM

GROMMET

SCREW LOCATION

BLOWER HSG ASSY

BRACKET

BRACKET
ENGAGEMENT

SEE DETAIL

CAPACITOR
OR POWER CHOKE
(WHEN USED)

BRACKET

SCREW

(GND)

BLOWER HSG ASSY

MOTOR, BLOWER

WHEEL, BLOWER

CUTOFF, BLOWER

DETAIL

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды