![background image](http://html1.mh-extra.com/html/carrier/69nt40-489-100-series/69nt40-489-100-series_operation-and-service-manual_2563838089.webp)
65
T-305
6.8.5 Installing the Components
a. Push pistons from the inside of the crankcasethrough
the cylinders, being careful not to break the rings.
Place rods so that the chamfered side will be against
radius of crankpins. Install the crankshaft and thrust
washer through the pump end of the compressor. En-
sure thrust washer is fitted on locating pin. Do not
damage main bearings. Bring rods in position against
crank bearings.
b. Install the pump end thrust washer on the two dowel
pins located on the bearing head. (See Figure 30,
page.)
CAUTION
Ensure that thrust washer does not fall off
dowel pins while installing oil pump.
CAUTION
The set screw on the crankshaft must be
removed for this type of oil pump.
(See
Figure 30, page 63.)
c. Install the bearing head assembly with a new gasket
on the compressor crankshaft. Carefully push oil
pump on by hand, ensuring that the thrust washer re-
mains on the dowel pins. The tang on the end of the
drive engages the slot in the crankshaft, and the oil
inlet port on the pump is aligned with the oil pickup
tube in the crankcase. The pump should mount flush
with the crankcase and should be oriented with the oil
pick up tube and oil inlet port aligned as shown in
Figure 30, page 63.
d. Align the gasket and install the eight capscrews in the
mounting flange. Refer to Table 18, page 83 for appli-
cable torque values.
e. Install matching connecting rod caps Be sure rod is
not bound and crankshaft will turn correctly as each
set of rod bolts is torqued.
f. Be sure key fits properly when installng rotor on shaft
Screw on equalizer tube and lock screw assembly
with lock washer and bend over tabs of lock washer.
Assemble suction strainer to motor and cover and
bolt cover to crankcase. Assemble valve plates and
gaskets. Assemble cylinder heads and gaskets. Turn
the shaft by hand to see that it moves freely.
g. Install the oil suction screen, the oil suction screen
hold down plate and the bottom plate.
6.8.6 Compressor Oil Level
CAUTION
Use only Carrier Transicold approved
Polyol Ester Oil (POE) -- Castrol-Icematic
SW20 compressor oil with R-134a. Buy in
quantities of one quart or smaller. When
using this hygroscopic oil, immediately
reseal. Do not leave container of oil open or
contamination will occur.
a. Checking the Oil Level in the Compressor.
1. Operate the unit in cooling mode for at least 20 min-
utes.
2. Check the front oil sight glass on the compressor to
ensure that no foaming of the oil is present after 20
minutes of operation. If the oil is foaming excessively
after 20 minutes of operation, check the refrigerant
system for flood-back of liquid refrigerant. Correct
this situation before performing the following step.
3. Turn unit off to check the oil level. The correct oil level
range should be between the bottom to one-eighth
level of the sight glass. If the level is above one-
eighth, oil must be removed from the compressor. To
remove oil from the compressor, follow step d in this
section. If the level is below the bottom of the sight
glass, add oil to the compressor following step b
below.
b. Adding Oil with Compressor in System
1. The recommended method is to add oil using an oil
pump at the oil fill valve (see item 11, Figure 27, page
61)
2. In an emergency where an oil pump is not available,
oil may be drawn into the compressor through the
suction service valve.
Connect the suction connection of the gauge man-
ifold to the compressor suction service valve port,
and immerse the common connection of the gauge
manifold in an open container of refrigeration oil.
Extreme care must be taken to ensure the manifold
common connection remains immersed in oil at all
times. Otherwise air and moisture will be drawn into
the compressor. Crack the suction service valve and
gauge valve to vent a small amount of refrigerant
through the common connection and the oil to purge
the lines of air. Close the gauge manifold valve.
With the unit running, frontseat the suction service
valve and induce a vacuum in the compressor crank-
case. SLOWLY crack the suction gauge manifold
valve and oil will flow through the suction service
valve into the compressor. Add oil as necessary.
c. Adding Oil to Service Replacement Compressor
Service replacement compressors are shipped without
oil. If oil is present in the crankcase, it must be tested to
ensure it is the correct oil and that the moisture level is
acceptable.
When adding oil to a service replacement compressor
add three liters (6.3 pints) using an oil pump at the oil fill
valve (see item 11, Figure 27, page 61). This quantity is
recommended to allow for return of any oil that may be in
the refrigerant system. Install compressor and recheck
oil level after it is placed in operation.
Содержание 69NT40-489-100 Series
