Carlisle Ransburg A14895 Series Скачать руководство пользователя страница 32

Страница: 32 / 32

This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited

warranty. The use of any parts or accessories, from a source other than Carlisle Fluid

Technologies, will void all warranties. Failure to reasonably follow any maintenance

guidance provided, may invalidate any warranty.

For specific warranty information please contact Carlisle Fluid Technologies.

WARRANTY POLICY

For technical assistance or to locate an authorized distributor, contact one of our international sales

and customer support locations.

For the latest information about our products, visit www.carlisleft.com.

Carlisle Fluid Technologies is a global leader in innovative finishing technologies.

Carlisle Fluid Technologies reserves the right to modify equipment specifications without prior notice.

BGK

, Binks

, DeVilbiss

, Hosco

, MS

, and Ransburg

are registered trademarks of Carlisle Fluid Technologies, Inc.

Tel: +44 (0)1202 571 111

Fax: +44 (0)1202 573 488

Tel: +8621-3373 0108

Fax: +8621-3373 0308

Tel: +81 45 785 6421

Fax: +81 45 785 6517

Tel: +61 (0) 2 8525 7555

Fax: +61 (0) 2 8525 7575

Region

Americas

Europe, Africa

Middle East, India

China

Japan

Australia

Industrial / Automotive

Tel: 1-800-992-4657

Fax: 1-888-246-5732

Automotive Refinishing

Tel: 1-800-445-3988

Fax: 1-800-445-6643

SI-21-06-R1 (11/2021)

32 / 32

www.carlisleft.com

Return To Contents

Содержание Ransburg A14895 Series

































Результаты поиска

Содержание Ransburg A14895 Series

Отзывы:

Carlisle Ransburg A14895 Series, Инструкция по эксплуатации, Страница: 32 / 32

Результаты поиска

Содержание Ransburg A14895 Series

Отзывы: