Carlisle Ransburg A14895 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

Carlisle Ransburg A14895 Series Скачать руководство пользователя страница 13

OPERATION

EN

SI-21-06-R1 (11/2021)

13 / 32

www.carlisleft.com

Step 6

Step 5

Pull off spacer plate from turbine assembly

and set aside until later.

Inspect Front Thrust Bearing Mounted in the

Bearing Housing:

Inspect the rear bronze bearing in the turbine housing,

if the bearing face is “Discolored severely” the entire

bearing housing must be replaced. The circular ring

that connects air bearing jets must be intact to assure

turbine motor will function at factory load specifications.

VISUAL APPEARANCE OF NEW

FRONT THRUST BEARING

CIRCULAR RING MUST BE

PRESENT TO REPAIR!!!

Figure: 1-5

IMPORTANT NOTE:

The circular ring connecting the bearing air holes

on the front thrust bearing surface if the ring is

broken or completely worn down, the bronze bear-

ing is no longer any good and the assembly needs

to be replaced.

VISUAL EXAMPLE OF:

NON-REPAIRABLE FRONT

THRUST BEARING.

Figure 1-6: Front thrust bearing in turbine housing.

AIR BEARING JETS AND CIRCULAR JET

RING DAMAGED BEYOND REPAIR.

Figure 1-6A

“DO NOT REMOVE”

FRONT

THRUST BEARING - IT IS

PRESET BY THE SUPPLIER. IT

IS NOT FIELD REPLACEABLE

Bearing Air O-Ring,

retain do not lose.

Return To Contents

«
...
11
12
13
14
15
...
»

Содержание Ransburg A14895 Series

































Отзывы:

Нет отзывов