Carlisle Ransburg A14895 Series Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 32

Carlisle Ransburg A14895 Series Скачать руководство пользователя страница 27

OPERATION

EN

SI-21-06-R1 (11/2021)

27 / 32

www.carlisleft.com

Step 30A

Step 29A

Assemble Rear Cover onto

Bearing Housing

Assemble Star Head Screws:

Replace star screws into rear cover of turbine

motor. Do not tighten leave loose and proceed

to next step.

OPTIONAL ALIGNMENT TOOL METHOD

Figure 1-30A

A13268-00 Alignment Ring

Figure 1-29A

Align housing, Spacer and Rear Cover

in Alignment Ring

Align Turbine Motor in Alignment Ring:

Carefully align turbine motor as shown in Figure

1-30A. Once aligned, check shaft for free rotation

by hand then proceed to tighten #10 Star screws to

12-15 lbs.-in. (1.4-1.7 N-m) torque using an alter-

nating pattern. The shaft should be free moving

during the screw tightening process as well as af-

ter. If not spinning free, loosen screws and reposi-

tion unit in the alignment ring, then repeat process.

Remove large diameter rear O-Ring

during assembly.

Return To Contents

«
...
25
26
27
28
29
...
»

Содержание Ransburg A14895 Series

































Отзывы:

Нет отзывов