Carlisle Ransburg A14895 Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 32

Carlisle Ransburg A14895 Series Скачать руководство пользователя страница 16

OPERATION

EN

SI-21-06-R1 (11/2021)

16 / 32

www.carlisleft.com

Step 11

Step 10

(Cont.)

Step 12

Dual Bearing Inspection &

Repair Process

Extract O-rings from bearing as shown in

Figure 1-10A.

Figure 1-10A

Figure 1-11

Figure 1-12

The radial bearings may be soaked in a solvent

compatible with the paint debris intrusion. Use of

an Ultrasonic cleaner may aid in loosening of the

foreign material.

Air Bearing Jet Inspection:

Using a .004 inch (0.102mm) dia. wire inspect all

bearing air jet holes in both bearings making sure

they are clean and free of debris. Blocked holes re-

duce the load capacities of the turbine motor allowing

it to fail prematurely. If holes are blocked and cannot

be cleared with wire, replace with new bearings.

Do Not Change Bearing Jet Hole

Size - Performance and motor life

will be affected.

Polish ID of Bearing:

Dependent upon shaft contact to the ID of the

bearing it may be necessary to polish the inside

diameter of the bearing as shown in Figure 1-12.

Polish bearing in circular (rotation)

motion not in linear direction use

only abrasive paper/cloth 2/0.

Return To Contents

«
...
14
15
16
17
18
...
»

Содержание Ransburg A14895 Series

































Отзывы:

Нет отзывов