manualshive.com logo in svg

Carlisle Ransburg A14895 Series, Инструкция по эксплуатации, Страница: 30 / 32

Поделиться
Скачать
Carlisle Ransburg A14895 Series Скачать руководство пользователя страница 30

PARTS IDENTIFICATION

EN

SI-21-06-R1  (11/2021)

30 / 32

www.carlisleft.com

1 

A12907-00 

1 

SCREW KIT (6 SCREWS)

2 

A12908-00 

1 

O-RING KIT (16 O-RINGS) (SEE KIT BREAKDOWN FOR EACH O-RING)

3 

A14901-00 

1 

SHAFT AND SPACER ASSEMBLY KIT

4 

A14902-00 

1 

REAR COVER ASSEMBLY WITH THRUST BEARING

5 

A14898-00 

2 

RADIAL BEARING

6 

A14899-00 

2 

RADIAL LOCATION PIN (2 PER ASS’Y REQ’D.)

7 

A12961-00 

2 

SPRING (2 PER ASS’Y REQ’D.)

8A 

A14897-00 

1 

BODY WITH THRUST BEARING (WITH SHAPE AIR HOLES)

8B 

A14904-00 

1 

BODY WITH THRUST BEARING (NO SHAPE AIR HOLES)

2A 

A13259-00 

RADIAL BEARING O-RINGS (4 REQUIRED PER ASSEMBLY)

2B 

A13260-00 

REAR COVER OUTSIDE DIAMETER O-RINGS

2C 

A13261-00 

BEARING AIR O-RINGS (3 REQUIRED PER ASSEMBLY)

2D 

A13262-00 

BRAKE AIR, REAR COVER FACE, O-RINGS

2E 

A13263-00 

TURBINE AIR, REAR COVER FACE, O-RINGS

2F 

A13264-00 

SPINDLE BODY, FRONT, OUTSIDE DIAMETER, O-RINGS

2G 

A13265-00 

SPINDLE BODY, FRONT FACE, LARGE DIAMETER, O-RINGS

2H 

A13266-00 

RADIAL LOCATION PIN FOR BEARING LOCATOR, O-RINGS (4 REQ’D. PER ASS’Y.)

Description

Item No.

SPINDLE REPLACEMENT PARTS

Part No.

Qty

Where Used

Item No.

A12908 O-RING KIT

Part No.

1 

RPM-63 

2 

SANDPAPER STRIP

2 

SSC-6001 

1 

LINT FREE TISSUE

3 

RPM-62-1 

2 

SANDPAPER DISC

4 

A13343-00 

2 

WIRE, 6 1/4”

5 

A12907-00 

1 

KIT, SCREW

6 

A14898-00 

2 

BEARING

7 

A12961-00 

2 

SPRING

8 

A12908-00 

1 

O-RING KIT

9 

SI-21-06 

1 

SERVICE INSTRUCTION (A14895-XX)

Description

Item No.

SERVICE KIT A12951-02 (CLEANING AND BEARING)

Part No.

Qty

Return To Contents

Содержание Ransburg A14895 Series

































Отзывы:

Нет отзывов