Carel humiSteam Basic UE001, Руководство пользователя, Страница: 67 / 84

2 7
ENG
“UE B A SIC” +0300042IE - rel . 1 . 6 - 21 . 11 . 2019
1
2
3
1
2
3
A
B
C
F
E
D
A
2
3
3
1
1
2
B
A
B
C
F
E
D
Fig. 9.f
Three-phase and sigle-phase models UE01 to UE018
UE00 1 - 3 - 9
single -p hase
75... 1 2 5 0 μS
1 = A
2 = D
75... 1 2 5 0 μS
1 = A
2 = C
3 = E
UE00 3 200 - 2 3 0 - 400 - 4 6 0 V
three -p hase
A
C E
A
D
75... 1 2 5 0 μS
1 = A
2 = C
3 = E
UE005-8 400 - 4 6 0 - 575 V
three -p hase
C E
A
75... 1 2 5 0 μS
1 = A
2 = C
3 = E
UE00 1 0- 1 8 400 - 4 6 0 - 575 V
three -p hase
C E
A
UE005 200 ... 2 3 0 V
single -p hase
1 75... 3 5 0 μS
1 = A - E - C
2 = B - F - D
3 5 0 ... 1 2 5 0 μS
1 = A - B - C
2 = D - E - F
A
F
E
B
C
D
UE005-8 / UE0 1 0- 1 5
200 ... 2 3 0 V three -p hase
75... 3 5 0 μS
1 = A - D
2 = B - E
3 = C - F
3 5 0 ... 1 2 5 0 μS
1 = A - B
2 = C - D
3 = E - F
A
F
E
B
C
D
9.6 Cleaning and maintenance of the other
components
•
when cleaning plastic components do not use detergents or solvents;
•
scale can be removed using a solution of 20% acetic acid and then
rinsing with water .
Maintenance checks on other components:
Ƒ
fi ll solenoid valve . A fter having disconnected the cables and the
tubing , remove the solenoid valve and make sure the inlet fi lter is
clean; if necessary , clean with water and a soft brush;
Ƒ
manifold with drain pump . Check that there are no solid residues
in the cylinder attachment , remove any impurities . Check that the
gasket (o - ring) is not damaged or cracked , replace if necessary . Check
that there are no solid residues in the drain hose;
Ƒ
drain pump . Disconnect the power supply , remove the pump and
clean any impurities . Clean the tank from any deposits and check that
the water fl ows freely from the tank to the drain (corresponding to
the drain pump);
Ƒ
fi ll tank . Check that there are no obstructions or solid particles and
that the conductivity measuring electrodes are clean , remove any
impurities and rinse;
Ƒ
internal tubing kit . Check that the pipes and hoses are free and clear
of impurities , remove any impurities and rinse .
Ƒ
Important : after having replaced or checked the water circuit ,
make sure that the connections are tight . Restart the unit and run
a number of fi ll and drain cycles (from 2 to 4) , after which , applying the
safety procedure , check for any water leaks .
Fuses in the auxiliary circuits
Fuses UE00 1 ... 0 1 8 UE 0 2 5... 06 5 ( 400 V ) UE0 2 5... 04 5 ( 23 0V )
F1 e F2 1 A fast - blow , 10 , 3x38 2 A fast - blow ,
10 , 3x38
F3 1 A fast - blow ,
5x20 ceramic
1 A fast - blow , 10 , 3x38
F4 4 A T fast - blow 5x20 ceramic
T ab. 9.g