Carel EVD Evolution Twin, Руководство пользователя

Страница: 14 / 68

ENG
“EVD Evolution TWIN” +0300006EN - rel. 2.6 - 31.01.2019 14
3. USER INTERFACE
The user interface consists of 8 LEDs that display the operating status, as
shown in the table:
VBA
T
G0
G
E
X
V connection Power Supply Relay
NO 1
COM 1
4 2 3 1
GND V REF S1 S2 S3 S4 DI1 DI2
Analog – Digital Input Network
GND Tx/Rx
EVD
evolution
twin
Fig. 3.a
Key:
LED On Off Flashing
NET Connection active No
connection Communication error
OPEN A/B Opening valve A/B - Driver A/B disabled (*)
CLOSE A/B Closing valve A/B - Driver A/B disabled (*)
OPEN B/
CLOSE B - - EVD Evolution TWIN
operating as single
driver
A
/
B
Active alarm driver A/B - -
Controller powered Controller off Wrong power supply
(see chap. on Alarms)
Tab. 3.a
(*) Awaiting completion of the initial configuration
3.1 Assembling the display board (accessory)
The display board, once installed, is used to perform all the configuration and
programming operations on the two drivers. It displays the operating status,
the significant values for the type of control that the drivers are performing
(e.g. superheat control), the alarms, the status of the digital inputs and the
relay outputs. Finally, it can save the configuration parameters for one
controller and transfer them to a second controller (see the procedure for
uploading and downloading the parameters).
For installation:
•
remove the cover, pressing on the fastening points;
•
fit the display board, as shown;
•
the display will come on, and if the controller is being commissioned, the
guided configuration procedure will start.
press
press
Fig. 3.b
Important: the controller is not activated if the configuration
procedure has not been completed.
The front panel now holds the display and the keypad, made up of 6 buttons,
that, pressed alone or in combination, are used to perform all the configuration
and programming operations on the controller.
3.2 Display and keypad
The graphic display shows two variables for each driver (A, B), the control
status of the driver, activation of the protectors, any alarms and the status of
the relay output.
Surriscaldam.
4.9 K
Apertura
valvola
44 %
ON
MOP
ALARM
-- Rele
1
2
3
4
5
7
A/B
6
T
8
Fig. 3.c
Key:
1 variable 1 on the display (driver A/B)
2 variable 2 on the display (driver A/B)
3 relay status (driver A/B)
4 alarm (press “HELP”)
5 protector activated
6 control status
7 current display: driver A/driver B
8 adaptive control in progress
Messages on the display
Control status Active protection
ON Operation LowSH Low superheat
OFF Standby LOP Low evaporation
temperature
POS Positioning MOP High evaporation
temperature
WAIT Wait HiTcond High condensing
temperature
CLOSE Closing
INIT Valve motor error recognition
procedure (*)
TUN Tuning in progress
Tab. 3.b
(*) The valve motor error recognition procedure can be disabled. See
paragraph 9.5.
(**) Only if EVD Evolution TWIN is operating as a single driver or programmable
superheat control is enabled.
Keypad
Button Function
Prg
•
opens the screen for entering the password to access
programming mode.
•
if in alarm status, displays the alarm queue;
•
in the “Manufacturer” level, when scrolling the parameters,
shows the explanation screens (Help);
•
pressed together with ENTER, switches the display from one
driver to the other
Esc
•
exits the Programming (Service/Manufacturer) and Display
modes;
•
after setting a parameter, exits without saving the changes.
UP/DOWN
•
navigates the screens on the display;
•
increases/decreases the value.
ENTER
•
switches from display to parameter programming mode;
•
confirms the value and returns to the list of parameters;
•
pressed together with HELP, switches the display from one
driver to the other.
Tab. 3.c
Note: :
the variables displayed as standard can be selected by
configuring the parameters “Variable 1 on display” and “Variable 2 on display”
for each driver. See the list of parameters.