
24
e-drofan 030221265 - rel. 1.0 - 04.08.2005
Nel Broadcast extended gli indirizzi consentiti vanno da 1 a 15; impostando 0 è
possibile inserire l’indirizzo tramite il terminale acqua (vedere sezione “impostazioni
avanzate”), in questo modo il sistema può essere riconfi gurato semplicemente
collegando il terminale.
Una installazione broadcast extended può essere facilmente commutata
in un sistema idronico tramite la modifi ca degli indirizzi seriali e
l’impostazione di pochi parametri (vedere sezione “impostazioni
avanzate” e “sistemi idronici”).
Nella seguente tabella sono riportate le impostazioni per ottenere i relativi
indirizzi (notazione binaria):
Impostazione dip switch
Indirizzo associato
1 2 3 4 5 6 7 8 9 10
ON
Default=1 (indirizzo seriale impostabile da
terminale acqua)
1 2 3 4 5 6 7 8 9 10
ON
1
1 2 3 4 5 6 7 8 9 10
ON
2
1 2 3 4 5 6 7 8 9 10
ON
3
1 2 3 4 5 6 7 8 9 10
ON
4
1 2 3 4 5 6 7 8 9 10
ON
5
1 2 3 4 5 6 7 8 9 10
ON
6
1 2 3 4 5 6 7 8 9 10
ON
7
1 2 3 4 5 6 7 8 9 10
ON
8
1 2 3 4 5 6 7 8 9 10
ON
9
1 2 3 4 5 6 7 8 9 10
ON
10
1 2 3 4 5 6 7 8 9 10
ON
11
1 2 3 4 5 6 7 8 9 10
ON
12
1 2 3 4 5 6 7 8 9 10
ON
13
1 2 3 4 5 6 7 8 9 10
ON
14
1 2 3 4 5 6 7 8 9 10
ON
15
Tab. 3.2
I dip switch 9 e 10 permettono di impostare la velocità di comunicazione sul
CANbus e devono essere settati entrambi nella stessa posizione.
dip 9 e 10 ON= 125 kbit/s
dip 9 e 10 OFF= 62.5 kbit/s
dip 8= deve rimanere sempre ON per l’utilizzo della scheda seriale sull’e-drofan.
Dopo ogni variazione apportata al dip switch l’e-drofan deve essere
disalimentato e rialimentato per rendere operativa la modifi ca.
La scheda seriale è dotata di tre led che permettono di visualizzarne lo stato e il
funzionamento. Il led verde indica che la scheda seriale è alimentata (dall’e-drofan)
mentre i led giallo e rosso indicano lo stato della comunicazione seriale. All’avvio i
due led (rosso e giallo) si accendono simultaneamente, nel caso di comunicazione
corretta si spegne prima il led rosso, poi quello giallo infi ne inizia il lampeggio
del LED giallo (ricezione dati in corso) o LED rosso (trasmissione dati in corso).
Se entrambe i led sono spenti in modo stabile la comunicazione è interrotta (sul
master il led rosso continua a lampeggiare).
In the extended broadcast, the available addresses range from 1 to 15; setting
0 allows the address to be entered from the acqua terminal (see the section on
“advanced settings”), in this way the system can be reconfi gured by simply connec-
ting the terminal.
An extended broadcast installation can be easily converted to a hydronic
system by modifying the serial addresses and setting a few parameters
(see the section on “advanced settings” and “hydronic systems”).
The following table shows the settings required to confi gure the corresponding
addresses (binary notation):
Dipswitch setting
Address associated
1 2 3 4 5 6 7 8 9 10
ON
Default=1 (serial address set from the acqua
terminal)
1 2 3 4 5 6 7 8 9 10
ON
1
1 2 3 4 5 6 7 8 9 10
ON
2
1 2 3 4 5 6 7 8 9 10
ON
3
1 2 3 4 5 6 7 8 9 10
ON
4
1 2 3 4 5 6 7 8 9 10
ON
5
1 2 3 4 5 6 7 8 9 10
ON
6
1 2 3 4 5 6 7 8 9 10
ON
7
1 2 3 4 5 6 7 8 9 10
ON
8
1 2 3 4 5 6 7 8 9 10
ON
9
1 2 3 4 5 6 7 8 9 10
ON
10
1 2 3 4 5 6 7 8 9 10
ON
11
1 2 3 4 5 6 7 8 9 10
ON
12
1 2 3 4 5 6 7 8 9 10
ON
13
1 2 3 4 5 6 7 8 9 10
ON
14
1 2 3 4 5 6 7 8 9 10
ON
15
Table 3.2
Dipswitches 9 and 10 are used to set the communication speed on the CANbus
and must be both set in the same position.
dip 9 and 10 ON= 125 kbit/s
dip 9 and 10 OFF= 62.5 kbit/s
dip 8= must always remain ON for the use of the serial board on the e-drofan.
After each variation made to the position of the dipswitches, the e-drofan must be
switched off and on again to make the changes operational.
The serial board is fi tted with three LEDs to display the operating status. The green
LED indicates that the serial board is on (power from the e-drofan) while the
yellow and red LEDs indicate the serial communication status. When starting, the
two LEDs (red and yellow) come on together, in normal communication fi rst the
red LED goes off, then the yellow LED, and fi nally the yellow LED (data reception
in progress) or red LED (data transmission in progress) starts fl ashing. If both the
LEDs are off steady communication is interrupted (the red LED continues fl ashing
on the master).
SE
Z
ION
E I
I
: installazione/
installation
reti broadcast /
broadcast net
works
Fig. 3.20
dip switch: indirizzo seriale /
serial address
Содержание e-drofan
Страница 2: ......
Страница 4: ...4 e drofan manual 030221265 rel 1 0 04 08 2005...
Страница 6: ...6 e drofan manual 030221265 rel 1 0 04 08 2005...
Страница 59: ......