Canon PIXMA MX870 Series Скачать руководство пользователя страница 18

Страница: 18 / 66

##111

TX / RX Memory error

- Eliminate all the data, and

##114

RTN has been received.

- Increase the transmission level of

the sending machine.

##200

A carrier has not been detected for 5 seconds during image
reception.

- Increase the transmission level of

the sending machine.

##201

TX / RX DCN has been received in a method other than the binary

procedure.

- Set the other machine ready for

reception.

##204

DTC has been received even when there is no sending data.

##220

TX / RX System error (main program hang-up)

- Turn the machine off, and turn it

on again

- Modular board
- Logic board

##224

TX / RX An error has occurred in the procedure signal in G3

transmission.

##226

TX / RX The stack pointer has shifted from the RAM area.

- Turn the machine off, and turn it

on again.

##229

The recording area has been locked for 1 minute.

- After the area is unlocked, print

the recorded image.

##232

The encoder control unit has malfunctioned.

- Modular board
- Logic board

##237

The decoder control unit has malfunctioned.

- Modular board
- Logic board

##238

The print control unit has malfunctioned.

- Modular board
- Logic board

##261

TX / RX A system error has occurred between the modem and the system

control board.

- Modular board
- Logic board

##280

Re-transmission of the procedure signal has been attempted the
specified number of times, but failed.

- Try a higher transmission level.

##281

Re-transmission of the procedure signal has been attempted the
specified number of times, but failed.

- Try a higher transmission level.

##282

Re-transmission of the procedure signal has been attempted the
specified number of times, but failed.

- Try a higher transmission level.

##283

Re-transmission of the procedure signal has been attempted the
specified number of times, but failed.

- Try a higher transmission level.

##284

After TCF transmission, DCN has been received.

- Set the receiving machine ready

for reception.

##285

After EOP transmission, DCN has been received.

- Re-send the fax.

##286

After EOM transmission, DCN has been received.

- Re-send the fax.

##287

After MPS transmission, DCN has been received.

- Re-send the fax.

##288

After EOP transmission, a signal other than PIN, PIP, MCF,
RTP, RTN has been received.

##289

After EOM transmission, a signal other than PIN, PIP, MCF,
RTP, RTN has been received.

##290

After MPS transmission, a signal other than PIN, PIP, MCF,
RTP, RTN has been received.

##670

In V.8 late start, the DIS V.8 ability from the receiving machine
was detected, and CI was sent in response; however, the
procedure failed, causing T1 time-over.

- In bit 0 of the service data #1

SSSW SW28, prohibit the V.8 /
V.34 procedure of the sending

15 / 63

Содержание PIXMA MX870 Series



































































Результаты поиска

Содержание PIXMA MX870 Series

Отзывы:

Похожие инструкции для PIXMA MX870 Series

Бренды по названию

Популярные бренды

Canon PIXMA MX870 Series, Руководство по обслуживанию

Результаты поиска

Содержание PIXMA MX870 Series

Отзывы:

Похожие инструкции для PIXMA MX870 Series

Бренды по названию

Популярные бренды