Canon imageRunner 2022, Руководство по обслуживанию

Страница: 334 / 418

Chapter 15
15-12
Use it to select an appropriate reception mode after transmission of the CFR signal.
If errors occur frequently at time of reception because of the condition of the line, select 'high speed' for reception mode and, at the same time, selects 'do not receive'
for 'ECM reception.'
Memo:
Any of the following error codes may be indicated at time of reception because of line condition
##0107, ##0114, ##0201
Be sure to change bit 4 before changing this bit; if errors still occur, change this bit.
When 'high speed' is selected, only high-speed signals (images) will be received after transmission of the CFR signal.
15.3.4.4 Detailed Discussions of Bit 4
0017-6060
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to select the time length during which low-speed signals are ignored after transmission of the CFR signal.
If the condition of the line is not good and, therefore, the reception of image signals is difficult, select '1500 ms.'
15.3.4.5 Detailed Discussions of Bit 5
0017-8523
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
In the countries that need approval of CI signal frequency check, no checking on frequency set at PBX when changing the frequency to PSTN setting and PBX
setting for frequency checks.
15.3.4.6 Detailed Discussions of Bit 6
0017-6063
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Selects whether or not to transmit CNG signal during manual transmission.
In manual transmitting to a fax with the FAX/TEL switching mode, if there are frequent errors due to failure to switch to fax mode, select "Transmitted" for the
CNG signal.
15.3.4.7 Detailed Discussions of Bit 7
0017-6064
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Selects whether or not to transmit CED signals during manual reception. If the other fax does not transmit even when you start manual reception, select "Transmit-
ted" for the CED signal.
15.3.5 SSSW-SW05
15.3.5.1 List of Functions
0017-6065
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
T-15-4
15.3.5.2 Detailed Discussions of Bit 1
0017-6066
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text mode.
Scanning direction in conversion follows the Bit 2 setting of SW14.
15.3.5.3 Detailed Discussions of Bit 2
0017-6067
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text/photo mode while bit 1 is set to '1'.
Scanning direction in conversion follows the Bit 2 setting of SW14.
15.3.6 SSSW-SW12
15.3.6.1 List of Functions
0017-6068
iR2022i / iR2025 / iR2030 / iR2018 / iR2022 / iR2018i
Bit Function 1 0
0 not used - -
1 Conversion from mm to inch (text mode) convert do not convert
2 Conversion from mm to inch (text/photo mode) convert do not convert
3 not used - -
4 not used - -
5 not used - -
6 not used - -
7 not used - -