Canon EOS C300 Mark II, Инструкция по эксплуатации

Страница: 201 / 223

201
Troubleshooting
Even after stopping recording, the access indicator stays illuminated in red.
- The clip is being recorded on the card. This is not a malfunction.
appears in yellow on the screen.
- The camera’s internal temperature has reached a predetermined level. You can continue using the camera.
appears in red on the screen.
- The camera’s internal temperature has risen further while appeared in yellow on the screen.
- In mode, or in mode when [System Setup]
>
[Fan]
>
[Mode] is set to [Always On], turn off the camera
and wait until the temperature has decreased.
- In mode, if the fan mode is set to [Automatic] and the fan was turned off while recording, the fan will turn on
automatically (in that case,
`
will appear on the screen).
i
appears on the screen.
- The camera and lens cannot communicate normally. Clean the lens’s contacts and reattach the lens.
appears in red on the screen
- The lithium button battery’s charge is low. Save the camera’s settings on an SD card (
A
146) and replace the lithium
button battery (
A
28). Then, restore the camera’s settings from the file saved on the SD card.
Picture and Sound
The LCD screen or viewfinder does not turn on.
- LCD screen: Make sure the unit cable connecting the camera’s VIDEO terminal and the monitor unit’s VIDEO terminal
is correctly connected on both sides.
- LCD screen: In mode, check that [Picture/Terminals Setup]
>
[Select Monitoring Devices] is set to an option
that includes [LCD]. When it is set to [MON.+HDMI+VF], the LCD screen will not turn on.
- In mode, when [Picture/Terminals Setup]
>
[Select Monitoring Devices] is set to [MON.+HDMI+LCD(VF)], the
LCD screen and viewfinder cannot be used simultaneously.
The peaking/magnification/zebra pattern/waveform monitor/B&W image does not appear on the screen.
- Check that display of the desired assistance function is enabled on the screen used with the corresponding output
settings.
Screen displays turn on and off repeatedly.
- The battery pack is exhausted. Replace or charge the battery pack.
- Remove the battery pack and reattach it correctly.
Abnormal characters appear on the screen and the camera does not operate properly.
- Disconnect the power source and reconnect it after a short time. If the problem still persists, use the [System Setup]
>
[Reset]
>
[All Settings] function. This resets all the camera’s settings to default values, except for the hour meter.
Video noise appears on screen.
- Keep a distance between the camera and devices that emit strong electromagnetic fields such as near powerful
magnets and motors, MRI machines or high-voltage power lines.
Horizontal bands appear on the screen.
- This is a phenomenon typical of CMOS image sensors when recording under some types of fluorescent, mercury or
sodium lamps. This is not a malfunction. You may be able to reduce the symptoms by setting the shutter speed mode
to [Speed] and the shutter speed to a value matching the frequency of the local electrical system: 1/50* or 1/100 for
50 Hz systems, 1/60 or 1/120 for 60 Hz systems.
* May not be available depending on the frame rate.
Audio cannot be recorded.
- When using the INPUT 1/INPUT 2 terminals: Make sure the unit cable connecting the camera’s AUDIO terminal and
the AUDIO terminal on the supplied monitor unit or optional MA-400 Microphone Adapter is correctly connected on
both sides.
- The external microphone connected to the INPUT 1/INPUT 2 terminal requires phantom power. Set the corresponding
INPUT 1/INPUT 2 audio input selection switch to MIC+48V (
A
98).
Audio is recorded at an extremely low level.
- When using the INPUT 1/INPUT 2 terminals: The audio level switch for CH1 or CH2 is set to M, and the recording level
is set too low. When using the MIC terminal: [Audio Setup]
>
[Audio Input]
>
[MIC Mode] is set to [Manual] and
[MIC Level] is set to a level too low. Check the audio level meter on the screen or rear panel and adjust the audio level
correctly (
A
99, 100).
- The microphone attenuator is on. Turn off the microphone attenuator (
A
100, 101).