Camplux CA686M-LP Скачать руководство пользователя

Страница: 59 / 84

During Installation of This Water Heater

Do’s

●

DO check inlet gas pressure to ensure that it is within the range specified on

the rating plate.

●

DO provide adequate air for combustion and ventilation as discussed in the

Use & Care Manual and the National Gas Code.

●

DO maintain proper clearances to combustibles as specified by applicable

code.

●

DO ensure that the flue terminal location complies with the guidelines found in

the Use & Care Manual and National Fuel Gas Code.

Don’t s

●

DON’T block or restrict Air Intake Opening located on the back side of the

water heater.

●

DON’T remove the front cover unless absolutely necessary. This should only

be done after being examined by a qualified service technician.

●

DON’T install this product where standing water may occur.

Mounting the CA686M Tankless Water Herter

Make sure the location of the water heater allows for

easy access and operation.
In case of dry wall or concrete wall use dry wall

anchors or lag bolts.
The water heater requires 120VAC/ 60Hz. Have a

receptacle with ground terminal near the water heater.

The length of the power supply cord is 5 feet.
Drill the holes as per the sizes in the figure to the left,

put 2 expansion screws into the top holes, and 2 rubber

screws into the bottom holes.
Hang up the water heater unit, tighten the expansion

screws, and put 2 wood thread screws into the bottom holes.

CAUTION: Reinforcement of the wall is required in case the wall is not

strong enough to hold the water heater.

Installation Holes

4-Ф0.4” deep 2”

288.5mm(11.36”)

198mm(7.80”)

107.5mm(4.23”)

90.5mm(3.56”)

633.23mm(24.93”)

Visit Us: Camplux.com

[email protected]

3330-A Marathon Ct Charleston, SC 29418

1(844) 538-7475

Содержание CA686M-LP





















































































Результаты поиска

Содержание CA686M-LP

Отзывы:

Похожие инструкции для CA686M-LP

Бренды по названию

Популярные бренды

Camplux CA686M-LP, Инструкция по использованию и уходу

Результаты поиска

Содержание CA686M-LP

Отзывы:

Похожие инструкции для CA686M-LP

Бренды по названию

Популярные бренды