Camplux CA686M-LP Скачать руководство пользователя

Страница: 73 / 84

Error code guide

When an error code is displayed :

●

Close the hot water faucet, turn off the switch on the remote control.

●

Wait for about 5 minutes before turning the switch on again.

●

Open the hot water faucet.

NOTICE: If an error code other than those listed below is displayed,

immediately turn off the hot water faucet, take note of the error code, turn

off the switch on the remote control and call the customer assistance

number.
If the error code remains shown:

●

Close the hot water faucet and turn off the switch on the remote control.

●

Take the proper action shown below and attempt operation of the water heater

again.

●

If the error code still shown:

●

Turn off the hot water faucet and turn off the switch on the remote control.

●

Take note of the error code displayed and call the customer service assistance

number in the “If You Need Service”.

Problem

Possible Cause

Not enough or no hot water

Water shut off valve is not fully opened

Open hot water faucet completely (the

main burner goes off when incoming water

volume is inadequate)
Allow piping too thaw
Check that proper power is being supplied

and or water supply is adequate
Turn the unit “ON” by the button on the

remote control
Increase the temperature setting
Check and replace if necessary
See instructions for Error Code and if

required,contact a dealer for service
Increase the temperature setting
Check and open the gas valve fully
Decrease the temperature setting

Allow more water to flow
Clean the filter with a booth brush
Normal operation. There is no need

to call for service. Check for error codes

Check shut off valve and open fully

Water piping is frozen

Hot water faucet is not fully opened

No electricity or water supply is cut off

Mixing valve malfunction (if applicable)
Error code displayed on remote

control panel

The gas valve is not fully opened
The temperature is set too high
Water shut off valve is not fully opened
Small amount water has been heated
Water filter is clogged
This function is no purge un-burned

gas 10-15 seconds

The temperature may be set too low

Unit is “ON”

The temperature may be set too low

Water not hot enough

Water too hot

Fan continues to rotate after

hot water faucet is closed

What To Do

Visit Us: Camplux.com

[email protected]

3330-A Marathon Ct Charleston, SC 29418

1(844) 538-7475

Содержание CA686M-LP





















































































Результаты поиска

Содержание CA686M-LP

Отзывы:

Похожие инструкции для CA686M-LP

Бренды по названию

Популярные бренды

Camplux CA686M-LP, Инструкция по использованию и уходу

Результаты поиска

Содержание CA686M-LP

Отзывы:

Похожие инструкции для CA686M-LP

Бренды по названию

Популярные бренды