Operating Instructions and Parts List
2
DC0300, FP2090, FP2091, FP2094 Series
GENERAL SAFETY
Since the air compressor and other
components (material pump, spray
guns, filters, lubricators, hoses,
etc.) used, make up a high pressure
pumping system, the following safety
precautions must be observed at all
times:
1. Read all manuals
included with this
product carefully. Be
thoroughly familiar with
the controls and the
proper use of the equipment.
2. Follow all local electrical and safety
codes as well as in the United
States, the National Electrical Codes
(NEC) and Occupational Safety and
Health Act (OSHA).
3. Only persons well acquainted
with these rules of safe operation
should be allowed to use the
compressor.
4. Keep visitors away and NEVER
allow children in the work area.
5. Wear safety glasses and
use hearing protection
when operating the unit.
6. Do not stand on or use the unit as
a handhold.
7. Before each use, inspect
compressed air system and
electrical components for signs of
damage, deterioration, weakness
or leakage. Repair or replace
defective items before using.
8. Check all fasteners at frequent
intervals for proper tightness.
Motors,
electrical
equipment and controls can cause
electrical arcs that will
ignite a fl ammable gas
or vapor. Never operate
or repair in or near a
fl ammable gas or vapor.
Never store fl ammable
liquids or gases in the vicinity of the
compressor.
Compressor parts
may be hot even if the unit is stopped.
9. Keep fingers away from a
running compressor; fast moving
and hot parts will cause injury and/
or burns.
10. If the equipment should start
to vibrate abnormally, STOP the
engine/motor and
check immediately for
the cause. Vibration is
generally a warning of
trouble.
11. To reduce fire hazard, keep engine/
motor exterior free of oil, solvent,
or excessive grease.
An ASME
code
safety relief valve
with a setting no higher
than 125 psi MUST be installed in the
tank for this compressor. The ASME
safety valve must have suffi cient fl ow
and pressure ratings to protect the
pressurized components from bursting.
See
compressor
specifi cation decal
for maximum operating pressure.
Do not operate with pressure switch
or pilot valves set higher than the
maximum operating pressure.
12. Never attempt to adjust ASME
safety valve. Keep safety valve
free from paint and other
accumulations.
Never use plastic
(PVC) pipe for
compressed air. Serious injury or death
could result.
Never
attempt to repair
or modify a tank! Welding, drilling or
any other modifi cation will weaken
the tank resulting in damage from
rupture or explosion. Always replace
worn, cracked or damaged tanks.
Drain liquid from
tank daily.
13. Tanks rust from moisture build-up,
which weakens the tank. Make
sure to drain tank regularly and
inspect periodically for unsafe
conditions such as rust formation
and corrosion.
14. Fast moving air will stir up dust
and debris which may be harmful.
Release air slowly when
draining moisture or
depressurizing the
compressor system.
15. To reduce the risk of electrical
shock, do not expose to rain. Store
indoors.
Indoor use only.
SPRAYING PRECAUTIONS
Do not
spray fl ammable
materials in vicinity of open fl ame or
near ignition sources including the
compressor unit.
16. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
17. Use a face mask / respirator when
spraying and spray in a well
ventilated area to prevent health
and fire hazards.
18. Do not direct paint or other
sprayed material at the compressor.
Locate compressor as far away
from the spraying area as
possible to minimize overspray
accumulation on the compressor.
19. When spraying or cleaning
with solvents or toxic chemicals,
follow the instructions
provided by the chemical
manufacturer.
HOSE PRECAUTIONS
20. Inspect hose before use.
Do
not
exceed working
pressure marked on hose.
Do not
twist,
bend knot, or abrade hose.
21. Do not wrap hose
around body.
Keep
away
from hot surfaces and
chemicals.
Introduction
R efer to Figure 3 to locate the
following items.
ON / OFF Switch ( I / O ) -
Push
switch to the ON (
I
) position to turn
compressor on. Push switch to the OFF
(
O
) position to turn compressor off.
This switch should be in the OFF (
O
)
position when connecting /
disconnecting power cord from
electrical outlet or when changing
tools.
MANUAL
Figure 1
www.campbellhausfeld.com
