CAMPAGNOLA MC Series, Руководство по эксплуатации и обслуживанию

Страница: 94 / 194

Campagnola Srl
ʹh^ED/EdEEDEh>ʹdƌĂŶƐůĂƟŽŶŽĨƚŚĞŽƌŝŐŝŶĂů/ŶƐƚƌƵĐƟŽŶƐ
ŽĚŝĐĞŵĂŶƵĂůĞϬϯϭϬ͘ϬϮϱϮͲsĞƌ͘ϭ͘ϬͲZĞǀ͗͘ϬϬ͕ĂƚĂ͗ϬϱͬϬϱͬϮϬϭϯ
Check the compressor oil level X
&OHDQWKH¿OWHUFDUWULGJH
X
Let the engine run for about 2 minutes X
Change the compressor oil X
5HSODFHWKH¿OWHUFDUWULGJH X
5HSODFHWKHVLOHQFHU¿OWHURIWKHSLORWYDOYHXQORDGHU X
Check the belts tension X
Clean all the external parts of the compressor X
Empty the fuel tank and use up the carburettor residual
content X
As for the commercial components of the machine and their use and maintenance instructions, as well as
more information about the periodical controls, see the corresponding Use and Maintenance Manuals enclosed,
indicated in chapter 9.
For details about the operative modes please refer to this manual, above all to par. 7.1 and 7.2.
8. TROUBLESHOOTING
The following chart shows the list of the possible problems regarding the system supplied.
The column named “Cause” shows the reason of the problem.
The column named “Solution” shows the operations to perform to solve the problem.
PROBLEM CAUSE SOLUTION
Drop in air tank pressure while
machine and tools are not in use Air leaks from the connections &KHFN DOO ¿WWLQJV E\ XVLQJ VRDS\
water. The leak will be shown by
air bubbles.
Overheating of the compressor head
block (2)
,QVXI¿FLHQW YHQWLODWLRQ GXH WR
obstruction of the upper guard grids
RUGLUWDPRQJWKHKHDGEORFN¿QV
Check the grids or blow air among
WKHKHDGEORFN¿QV
Pressure over 11 bar and safety
valve (4) releasing air )DXOW\RUEDGO\DGMXVWHGSLORWYDOYH
unloader (5)
Take the machine to an Authorised
Service Point.
Pilot valve/unloader (5) making a
cracking noise
)DXOW\RUEDGO\DGMXVWHGSLORWYDOYH
unloader (5)
Take the machine to an Authorised
Service Point.
The compressor head block (2)
GRHVQRW¿OOWKHDLUWDQNDQGWKHWDQN
pressure remains low
• Slipping drive belt (20)
‡$LUOHDNIURPWKHKHDGEORFNMRLQW
or valves breakage
• Reset the belt tension or replace it.
• Take the machine to an Authorised
Service Point.
The tools do not work perfectly (slow
down). Lacking lubrication in the connected
tools Check the oil and the dosing level
of the air lubricating unit.
The tools do not work at all %DGO\DGMXVWHGDLUUHJXODWRU &KHFN WKH SUHVVXUH DQG DGMXVW LW
according to the manual instructions
of the connected tools.
WĂŐ͘ϵϯͲϭϵϮ