CAMPAGNOLA MC Series, Руководство по эксплуатации и обслуживанию

Страница: 88 / 194

Campagnola Srl
ʹh^ED/EdEEDEh>ʹdƌĂŶƐůĂƟŽŶŽĨƚŚĞŽƌŝŐŝŶĂů/ŶƐƚƌƵĐƟŽŶƐ
ŽĚŝĐĞŵĂŶƵĂůĞϬϯϭϬ͘ϬϮϱϮͲsĞƌ͘ϭ͘ϬͲZĞǀ͗͘ϬϬ͕ĂƚĂ͗ϬϱͬϬϱͬϮϬϭϯ
6.1 GENERAL INFORMATION
- Do not use the machine when the slope inclination is over 10% in any directions.
- 'RQRWOHDYHDQ\Q\ORQRUFORWKRUDQ\RWKHUNLQGRIÀDPPDEOHREMHFWVRQRUQHDUWKHFRPSUHVVRUKHDG
block and the engine.
- 8VHWKHPDFKLQHRQO\IRUWKHDERYHPHQWLRQHGSXUSRVHV$Q\RWKHUXVHFRXOGFDXVHLQMXULHVRUGDPDJHV
- Always move the machine by keeping both hands on the handle bar to avoid any overturning.
- Always check the safety device for perfect working conditions.
-
%HIRUHVWDUWLQJWKHPDFKLQHFKHFNWKDWLWVSRVLWLRQLVVWDEOHDQGVDIHDQGWKDWWKHUHDUHQRREMHFWV
among the moving parts.
- Follow the Manufacturer’s indications about the lubrication and working pressure regulation of the tools
to use.
- 'RQRWXVHWKHPDFKLQHLILWLVGDPDJHGEDGO\DGMXVWHGRULQFRPSOHWHO\DVVHPEOHG
- Be very careful in case of oil or fuel spills.
- Every time before starting the machine, check the engine and compressor head block oil levels, since
a low oil level would cause serious damages.
6.2 FUNCTIONING
!
ATTENTION
:KHQWKHPDFKLQHZRUNVWKHVORSHLQFOLQDWLRQVKDOOQRWEHRYHULQDQ\GLUHFWLRQVRWKHUZLVHLW
would cause engine or compressor head block damages.
6.2.1 REFUELLING
Refuel the machine with the engine off and cold and by means of adequate tools to avoid any fuel spills.
)LOOWKHIXHOWDQNXSVHHWKHHQJLQHPDQXDOHQFORVXUHFDUHIXOO\GU\LQJDQ\VSLOOVWRDYRLGDQ\¿UHGDQJHU
Note: Follow the regulations and indications in the engine manual.
6.2.2 STARTING
!
ATTENTION
%HIRUHVWDUWLQJWKHPDFKLQHRSHQWKHDLUWDQNH[KDXVWYDOYHV
7RVWDUWWKHHQJLQHLQWKHULJKWZD\UHDGLWVPDQXDOHQFORVXUH
6.2.3 ENGINE-DRIVEN COMPRESSOR RUNNING-IN
:KHQXVLQJWKHHQJLQHGULYHQFRPSUHVVRUIRUWKH¿UVWWLPHIRUDSURSHUUXQQLQJLQFDUU\RXWWKHIROORZLQJRSHUDWLRQV
in the following order:
1) Before starting the engine-driven compressor, open the air tank exhaust valves (14);
2) Start the engine-driven compressor and make it idle, without any pneumatic tools connected, for about 10
minutes, keeping the air tank exhaust valves (14) open;
3) Switch the engine-driven compressor off and close the air tank exhaust valves only after that the engine has
stopped and the machine is cold.
4) Only after closing the air tank exhaust valves, start the engine-driven compressor. After few seconds the
pneumatic self-regulation device will increase the engine rpm till reaching the pre-set pressure.
WĂŐ͘ϴϳͲϭϵϮ