California Instruments 2253i Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 157

background image

User Manual

2253i / 2253iX

AMETEK

California Instruments

124

VOLT FREQ MAX

This test will set the voltage and frequency to a level defined by Table 9-9. The test will last for 30
minutes. The test will be repeated using the voltage from Table 9-8 and frequency from Table 9-9. The
BACK key (backspace) will terminate the test at any time.

VOLT UNBALANCE

Standard/Group

RTCA

A(CF)

A(NF)

A(WF)

Voltage offset

8

8

8

10

Frequency

400

360/440

360/650

360/800

Standard/Group

Group1

Group2

Group3

Voltage offset

8

8

12

Frequency

400

360/650

360/800

Table 9-10: Emergency Voltage Unbalance

This test will change the output voltage for phase A and B to 122V and phase C to a voltage lower by a
value specified by an offset.  Refer to Table 9-10 for the offset value and the Frequency.  The test will
repeat with the same frequency and phase A and B volt is set to 100V and phase C set to a higher
voltage specified by the offset. The test will last 30 minutes.  The test will be repeated for a second
Frequency if applicable.  The test can be terminated at any time.

The BACK key (backspace) will terminate the test at any time.

«
...
122
123
124
125
126
...
»

Содержание 2253i






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2253i

Бренд: E-Lite Страницы: 4

Бренд: Park Tool Страницы: 2

Бренд: Gardner Denver Страницы: 27

Бренд: Bohell Страницы: 36

Бренд: Parkside Страницы: 107

Бренд: Würth Страницы: 12

Бренд: Klauke Страницы: 22

Бренд: Geberit Страницы: 152

Бренд: Black Ridge Страницы: 16

Бренд: Kett Страницы: 6

Бренд: Precision matthews Страницы: 3

Бренд: Taylor Страницы: 2

Бренд: Outils Wolf Страницы: 32

Бренд: Caen Страницы: 14

Бренд: Interchange Страницы: 24

Бренд: Kilews Страницы: 12

Бренд: ACDelco Страницы: 36

Бренд: marklin Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды