California Instruments 2253i Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 157

background image

User Manual

2253i / 2253iX

AMETEK

California Instruments

121

T1

0 Volt

F1

F2

T2

T3

Test no.:

21

22

23

24

25

26

Standard:

I

II

III

IV

V

VI

T1 (ms)

50

50

100

100

200

200

F1 (Hz)

360

Fmax

360

Fmax

360

Fmax

F2 (Hz)

Fmax

360

Fmax

360

Fmax

360

Fmax = 650 Hz for Group2/A(NF)
Fmax = 800 Hz for Group3/A(WF)
T2 = 20 msec
T3 = 5 msec

Figure 9-7: Power Interrupt for Group2/A (NF) and Group3/A(WF)

VOLTAGE SURGE

This test requires 160V output voltage. If the power source is set at the low voltage range, the high
voltage range will be selected before the test starts. At the end of the test, the power source will be
switched back to the low range automatically.

Voltage

Time

Seq. No.

RTCA

Group 1

Group 2

Group 3

ALL

1

115

115

115

115

5 Minute

2

160

160

160

170

30msec

3

115

115

115

115

5 Sec.

4

60

70

70

70

30msec

5

115

115

115

115

5 Sec.

Table 9-5: Normal VoltageSurge Sequence

The output voltage will follow the sequence in Table 9-5.  The above sequence will repeat itself three
times.  Each repeat will start from sequence two.  RTCA and Group 1 will run at 400 Hz. Group 2 and
A(NF)  will run at 360 Hz and 650 Hz. Group 3 and A(WF) will run at 360Hz and 800Hz.  The frequency
will return to the nominal setting when the test is completed.  The  BACK key (backspace) will
terminate the test at any time.

«
...
119
120
121
122
123
...
»

Содержание 2253i






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2253i

Бренд: Campbell Hausfeld Страницы: 8

Бренд: WAGNER Страницы: 40

Бренд: Mafell Страницы: 75

Бренд: Mafell Страницы: 46

Бренд: Xantrex Страницы: 64

Бренд: Sealey Страницы: 3

Бренд: HIKOKI Страницы: 24

Бренд: Omer Страницы: 2

Бренд: Bahco Страницы: 52

Бренд: Proluxe Страницы: 17

Бренд: Far Tools Страницы: 24

TRIO-PS-2G/3AC/24DC/40

Бренд: Phoenix Contact Страницы: 25

Бренд: Facom Страницы: 28

Бренд: Power works Страницы: 136

Бренд: BK Precision Страницы: 50

FORCEDRIVER WX270L

Бренд: Worx Страницы: 40

00136157 Fusion

Бренд: Hama Страницы: 9

Бренд: Tryton Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды