Caen DT5495 Скачать руководство пользователя страница 36

Страница: 36 / 61

CAEN

Electronic Instrumentation

UM6508

–

DT5495 User Manual rev. 0

Configuration ROM (0x8100-0x81FF)

The following registers contain module configuration information according to

Tab. 9.2

Only the 8 LSBs of each location of the Configuration ROM are significant.

Description

Address

Content

checksum

0x8100

An eight bit 2

’

s complement binary checksum. The

sum of the bytes starts from offset 0x8104 for the
number of bytes specified in the length field
(inclusive)

checksum_length2

0x8104

0x00

checksum_length1

0x8108

0x00

checksum_length0

0x810C

0x20

constant2

0x8110

0x84

constant1

0x8114

0x84

constant0

0x8118

0x01

c_code

0x811C

0x43

r_code

0x8120

0x52

oui2

0x8124

0x00

oui1

0x8128

0x40

oui0

0x812C

0xE6

version

0x8130

0x00

board2

0x8134

0x00

board1

0x8138

0x09

board0

0x813C

0xBF

revis3

0x8140

0x00

revis2

0x8144

0x00

revis1

0x8148

0x00

revis0

0x814C

PCB revision

sernum1

0x8180

Serial Number (MSB)

sernum0

0x8184

Serial Number (LSB)

Tab. 9.2:

ROM Address Map of the DT5495



Note:

The oui0/1 fields represent CAEN Manufacturer identifier (IEEE OUI), which is equal to 0x40E6.



Note:

The board serial number can be read with two accesses: if the serial number on the module front panel is 1245

(hex 0x4DD), for instance, the Serial Number’s MSB (0x8180) will be 0x04, while the Serial Number’s LSB (0x8184) will

be 0xDD.

Configuration and Status Registers (0x8200-0x83FF)

Address

Register/Content

Read/Write

0x8200

MFPGA firmware revision

0x8204 ÷ 0x8214

reserved

0x8218

Software reset

0x8220

Scratch register

R/W

0x8224 ÷ 0x83FC

reserved

Tab. 9.3:

CSR registers

Содержание DT5495






























































Результаты поиска

Содержание DT5495

Отзывы:

Похожие инструкции для DT5495

Бренды по названию

Популярные бренды

Caen DT5495, Руководство пользователя

Результаты поиска

Содержание DT5495

Отзывы:

Похожие инструкции для DT5495

Бренды по названию

Популярные бренды