Cabletron Systems TRMIM-20R Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 56

background image

INTRODUCTION

Page 1-4

It is possible to have several network types and media in one MMAC,
such as a shielded twisted pair token ring network and a thin-net
Ethernet network. There are a number of configuration guidelines
concerning multiple networks within an MMAC. These guidelines
are listed in Chapter 3, Installing the TRMIM-20R.

Several MMACs can be connected into the same ring network by
installing token ring concentrators (TRMIM-10R/TRMIM-20R) or
token ring repeaters (TRRMIM-16/TRRMIM-26). The choice between
using concentrators or repeaters depends on specific network
configurations.

The TRMIM-20R incorporates LANVIEW, a useful tool to help you
quickly diagnose physical layer network problems. Several LEDs
(light emitting diodes) are located at the front of the TRMIM-20R.
These LEDs indicate the ring speed, detection of a TRMIM-20R
hardware error, and when a specific port is attached to the ring.

A variety of network management tools can be used to control and
monitor the TRMIM-20R, including Cabletron Systems Local
Management, Cabletron Systems Remote LANVIEW Windows



, and

Cabletron Systems SPECTRUM



.

1.3 RELATED MANUALS

The manuals listed below should be used to supplement the
procedures and other technical data provided in this manual. The
procedures in them will be referenced, where appropriate, but will not
be repeated in this document.

Cabletron Systems’ Multi-Media Access Center Overview and
Set Up Guide.

Cabletron Systems’ TRMIM-10R Token Ring Concentrator
Media Interface Module Installation Guide.

Cabletron Systems’ TRMIM-12 Token Ring Media Interface
Module Installation Guide.

Cabletron Systems’ TRRMIM-16 Token Ring Repeater Media
Interface Module Installation Guide.

«
...
7
8
9
10
11
...
»

Содержание TRMIM-20R

























































Отзывы:

Нет отзывов

Похожие инструкции для TRMIM-20R

Бренд: Eaton Страницы: 10

Бренд: Ubiquiti Страницы: 22

Бренд: Google Страницы: 14

Бренд: FOR-A Страницы: 39

TE100-S16 - 10/100Mbps Ethernet Switch

Бренд: TRENDnet Страницы: 15

Бренд: QUNDIS Страницы: 42

BROADCAST POLLING FRAD BPF-14 BU

Бренд: DCB Страницы: 28

Бренд: Maipu Страницы: 26

Бренд: ADTRAN Страницы: 4

Бренд: Variscite Страницы: 17

Бренд: Teldat Страницы: 23

Бренд: Ubiquiti Страницы: 20

Бренд: TP-Link Страницы: 182

DHI-NVR5208-4KS2

Бренд: Dahua Страницы: 361

Бренд: Dahua Страницы: 489

Бренд: D-Link Страницы: 2

Surestore Tape Library Model 2/28

Бренд: HP Страницы: 110

Surestore Tape Library Model 2/15

Бренд: HP Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды