Cabletron Systems TRMIM-20R Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 56

background image

TESTING AND TROUBLESHOOTING

Page 4-1

CHAPTER 4

TESTING AND TROUBLESHOOTING

This section contains procedures to verify the cabling connecting the
TRMIM-20R to the Token Ring network and any attached stations. A
description of LANVIEW and its function in troubleshooting physical
layer network problems is also provided.

4.1 INSTALLATION CHECKOUT

Perform the following steps to check the installation of the
TRMIM-20R:

1.

Be sure that the Token Ring stations and the MMAC match the
AC power source (120 Vac or 240 Vac) and are powered on.

2.

Trace the ring path through the network, to be sure that there
are no breaks in the ring and that it is free from logical design
errors. While tracing the ring:

a.

Check each cable connection on the MIM.

b.

Verify that the pinout for every connector is correct.

c.

Check the cable conductors for continuity. Cable testers are
available for this task.

d.

Check each cable connection at patch panels and wall plates.

3.

Check the network ring speed:

a.

Check that the ring speed matches the station and cable
specifications mentioned in Chapter 2, Installation
Requirements/Specifications.

b.

Verify all devices on the ring network are set to the same ring
speed. Check all MIMs and stations in the network.

«
...
27
28
29
30
31
...
»

Содержание TRMIM-20R

























































Отзывы:

Нет отзывов

Похожие инструкции для TRMIM-20R

Бренд: H3C Страницы: 6

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 4

OfficeConnect 3CP4144

Бренд: 3Com Страницы: 2

Бренд: H3C Страницы: 60

Бренд: H3C Страницы: 149

Бренд: 3Com Страницы: 27

Бренд: Lanpro Страницы: 5

Бренд: Stephen Страницы: 102

NVIP- NVRA0104/GO

Бренд: Novus Страницы: 44

Бренд: Ravpower Страницы: 27

Бренд: StarTech.com Страницы: 9

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

Бренд: XtendLan Страницы: 52

Бренд: CalAmp Страницы: 115

Бренд: Solwise Страницы: 231

Бренд: Idis Страницы: 16

Бренд: ActionTec MI424WR Страницы: 3

Бренд: Supero Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды