Cabletron Systems TRMIM-20R страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 56

background image

INSTALLING THE TRMIM-20R

Page 3-1

CHAPTER 3

INSTALLING THE TRMIM-20R

This chapter contains instructions for installing the TRMIM-20R into
a Cabletron Systems’ MMAC. Instructions for connecting a Twisted
Pair Segment to the MIM for operation are also included. Check that
all requirements listed in Chapter 2, Installation Requirements/
Specifications, are met before installing the MIM.

3.1 UNPACKING THE TRMIM-20R

Prior to installation, you should visually inspect the MIM. Perform
the following steps to unpack the MIM:

1.

Carefully remove the MIM from the shipping box. Save the box
and materials in the event the unit has to be repackaged and
shipped.

CAUTION: The electronic components on the MIM are sensitive
to electrostatic discharges (ESD). Observe all ESD prevention
measures when handling the MIM. Static discharges will damage
the MIM.

2.

Remove the MIM from its protective plastic bag, holding only the
edges of the MIM or the metal front panel. Avoid touching the
components or the surface of the MIM. Set the MIM on top of its
protective bag in a static free area to prevent the MIM from being
damaged.

Contact Cabletron Systems Technical Support immediately if any
problems exist.

«
...
19
20
21
22
23
...
»

Содержание TRMIM-20R

























































Отзывы:

Нет отзывов

Похожие инструкции для TRMIM-20R

Бренд: IEI Technology Страницы: 86

Lite N42B1P Series

Бренд: Dahua Technology Страницы: 14

Бренд: NetComm Страницы: 69

Hotwire 8775 MSDSL

Бренд: Paradyne Страницы: 10

Бренд: Digisol Страницы: 22

B-Control Fader BCF2000

Бренд: Behringer Страницы: 13

NetCon FBR-1409TX

Бренд: LevelOne Страницы: 88

Fast EtherLink XL PCI 10/100BASE-TXNetwork Interface...

Бренд: 3Com Страницы: 12

Бренд: Airvana Страницы: 90

Бренд: InHand Страницы: 69

Routers and Switches

Бренд: Allied Telesis Страницы: 15

Бренд: Wieland Страницы: 2

Бренд: l-com Страницы: 11

Бренд: ADF Web Страницы: 20

Бренд: Billion Страницы: 20

Бренд: Encore Networks Страницы: 2

Бренд: Emerson Страницы: 8

Liebert NXL 250

Бренд: Emerson Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды