Cabletron Systems TRMIM-20R Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 56

background image

INSTALLING THE TRMIM-20R

Page 3-5

Attaching UTP Lobe Cables to the TRMIM-20R
To attach a UTP lobe cable to the TRMIM-20R:

1.

Connect the male RJ-45 connector from one end of the UTP lobe
cable to a port on the TRMIM-20R (see Figure 3-4).

2.

If a patch panel is to be used, connect the other end of the cable
to the appropriate patch panel jack. (Install RJ-45 to MIC
adapters as needed.)

3.

Repeat this process for each station

Attaching the UTP Cable at the Station
A Type 3 Media Filter must be installed at the station end of the lobe
cable. Some stations incorporate an internal filter and do not require
any additional equipment. If your station requires an external Type
3 Media Filter, install the filter between lobe cable and station port.
Otherwise, connect the stations to the wall plate using a Type 3 patch
cable. Attach one end of the patch cable to the wall plate and the
other to the station port.

«
...
23
24
25
26
27
...
»

Содержание TRMIM-20R

























































Отзывы:

Нет отзывов

Похожие инструкции для TRMIM-20R

Бренд: D-Link Страницы: 10

Бренд: Panasonic Страницы: 4

Бренд: Paradyne Страницы: 16

Бренд: LAWO Страницы: 154

Бренд: F-SECURE Страницы: 19

Бренд: ICP DAS USA Страницы: 48

Бренд: ICP DAS USA Страницы: 24

Бренд: ICP DAS USA Страницы: 4

Бренд: Paradyne Страницы: 2

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Nighthawk M6 Pro

Бренд: AT&T Страницы: 2

Бренд: NA Страницы: 22

Бренд: LevelOne Страницы: 26

EtherLink 3C905C-TX

Бренд: 3Com Страницы: 96

Бренд: Intercoax Страницы: 2

Бренд: Waver Страницы: 36

Бренд: UNICORECOMM Страницы: 19

Network Adapter AC AAP

Бренд: Extron electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды