Cabletron Systems TRMIM-20R страница 6 Скачать руководство пользователя | Manualshive

Страница: 6 / 56

background image

INTRODUCTION

Page 1-1

CHAPTER 1

INTRODUCTION

Welcome to the TRMIM-20R Token Ring Passive Concentrator
Media Interface Module Installation Guide. This guide is
designed to serve as a reference for the installation and
troubleshooting of Cabletron Systems’ TRMIM-20R.

The TRMIM-20R is a token ring network concentrator used in
conjunction with Cabletron System’s Multi Media Access Center
(MMAC). The TRMIM-20R provides ten trunk coupling unit ports
and passive Ring-In and Ring-Out ports. The TRMIM-20R is IEEE
802.5 compliant, and compatible with IBM products. Since the Ring-
In/Ring-Out ports are passive and do not regenerate signal timing,
Adjusted Ring Length (ARL) must be considered when planning cable
lengths.

Prior to installing and operating the TRMIM-20R, read through this
manual to familiarize yourself with its content and to gain an
understanding of the features of TRMIM-20R. A general working
knowledge of Token Ring (IEEE 802.5) networks will be helpful when
installing the TRMIM-20R.

1.1 USING THIS MANUAL

Chapter 1, Introduction, covers using this document, briefly
describes features of the TRMIM-20R and token ring, and lists
related manuals.

Chapter 2, Installation Requirements/Specifications, lists
network requirements that must be met before you install the
TRMIM-20R and specifications for the TRMIM-20R.

Chapter 3, Installing the TRMIM-20R, describes installing the
TRMIM-20R into the MMAC, connecting stations, and inserting the
TRMIM-20R into a token ring network.

«
...
4
5
6
7
8
...
»

Содержание TRMIM-20R

























































Отзывы:

Нет отзывов

Похожие инструкции для TRMIM-20R

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: Patton electronics Страницы: 51

Бренд: E-TOP Страницы: 76

Бренд: Netopia Страницы: 38

Бренд: dixell Страницы: 4

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: Radicom Страницы: 27

Бренд: VCS Страницы: 118

AT-8550/SP Series

Бренд: Allied Telesis Страницы: 114

Бренд: Belkin Страницы: 57

ExpressBox2 EB2

Бренд: Magma Страницы: 74

Бренд: Chase Research Страницы: 114

Бренд: Aaeon Страницы: 100

Бренд: Me Страницы: 28

Network Controller

Бренд: MikroTik Страницы: 6

DigitalMedia DM-RPP-K24

Бренд: Crestron Страницы: 2

Бренд: Microview Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды