Cabletron Systems TRMIM-20R страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 56

background image

INSTALLING THE TRMIM-20R

Page 3-7

The STP trunk cables are attached to the TRMIM-20R using male
DB-9 connectors. If a patch panel is to be used, connect Ring-In from
the patch panel to Ring-In of the TRMIM-20R and Ring-Out from the
patch panel to Ring-Out on the TRMIM-20R. When connections are
made between concentrators within the same closet, daisy-chain the
connections, Ring-In to Ring-Out, from concentrator to concentrator.
For some installations, DB-9 to MIC adapters may be needed.

NOTE: Wrap Jumper Plugs must be used for installations with no
external ring connections to the TRMIM-20R or to replace a trunk
cable to bypass a failed ring segment. Two plugs are provided with
each TRMIM-20R.

3.4 FINISHING THE INSTALLATION

«
...
25
26
27
28
29
...
»

Содержание TRMIM-20R

























































Отзывы:

Нет отзывов

Похожие инструкции для TRMIM-20R

Бренд: Variscite Страницы: 18

Бренд: UfiSpace Страницы: 32

Бренд: BWI Страницы: 5

Бренд: Lantech Страницы: 40

Бренд: Quantum Страницы: 7

Blue Gate ISDN BRI Brave

Бренд: Alphatech Страницы: 6

Бренд: HMS Страницы: 18

Бренд: MICRADIGITAL Страницы: 2

Бренд: BinTec Страницы: 2

Бренд: Eaton Страницы: 32

Бренд: ZyXEL Communications Страницы: 4

Бренд: BinTec Страницы: 35

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 8

AirProtect Enterprise Engine 6100

Бренд: 3Com Страницы: 12

Бренд: 2Wire Страницы: 20

Бренд: 3Com Страницы: 82

Бренд: MikroTik Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды