Cabletron Systems TRMIM-20R Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 56

background image

REQUIREMENTS/SPECIFICATIONS

Page 2-1

CHAPTER 2

INSTALLATION REQUIREMENTS/

SPECIFICATIONS

Before you attempt to install your TRMIM-20R, review the
installation requirements and operating specifications outlined in
this chapter. The conditions, guidelines and requirements described
in this chapter must be met to obtain satisfactory performance from
this equipment.

2.1 NETWORK REQUIREMENTS

Take care in planning and preparing the cabling and connections for
your network. The quality of the connections, the length of cables
and other conditions of the installation are critical factors in
determining the reliability of your network.

NOTE: While the TRMIM-20R supports voice grade UTP cabling,

some applications, where existing telephone voice grade UTP is used,
may be subject to crosstalk, electrical noise, signal attenuation or other
environmental factors that exceed acceptable limits. This could reduce
the maximum cable lengths or, in extreme cases, prevent using the
existing cables. In some cases acceptable performance will be obtained
by reducing the lobe length or rerouting the cable. Where more severe
interference is encountered, the installation of new cabling may be
necessary.

The following sections describe the network requirements for
TRMIM-20R operation, however, the same requirements apply
whenever UTP cabling is used within a passive ring segment.

2.1.1 Cable Types

Trunk Cabling - The TRMIM-20R supports IBM Type 1, 2, 6 and 9
shielded twisted pair cable.

«
...
9
10
11
12
13
...
»

Содержание TRMIM-20R

























































Отзывы:

Нет отзывов

Похожие инструкции для TRMIM-20R

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 40

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 4

AirPlus G DWL-G710

Бренд: D-Link Страницы: 5

MYDLINK DNR-322L

Бренд: D-Link Страницы: 4

mydlink DNR-312L

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 88

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 221

Express Ethernetwork DI-707P

Бренд: D-Link Страницы: 14

Бренд: Vanguard Страницы: 121

Бренд: 4RF Страницы: 7

S5500-HI Switch Series

Бренд: H3C Страницы: 180

Бренд: H3C Страницы: 84

Бренд: H3C Страницы: 281

Бренд: H3C Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды