Cabletron Systems TRMIM-20R Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 56

background image

INSTALLING THE TRMIM-20R

Page 3-8

Complete the installation by doing the following:

1.

Ensure the MMAC and the stations are powered on.

2.

Ensure that all LEDs on the MIM and any LEDs on the stations
are illuminated properly, with no error conditions shown. If they
are not in a normal condition, proceed to Chapter 4, Testing and
Troubleshooting.

The green Link Attached LEDs on the MIM should be illuminated
for each station inserted into the ring. The yellow 16Mb LED
should only be on if 16 Mbit/s ring speed is selected.

3.

Configure the networking software.

The TRMIM-20R is now ready for operation. Before placing the
network into service, test the installation thoroughly, making sure
that all stations are able to be addressed and that the data is being
relayed without error. Ensure that the networking software is
configured properly to match the installed network.

«
...
26
27
28
29
30
...
»

Содержание TRMIM-20R

























































Отзывы:

Нет отзывов

Похожие инструкции для TRMIM-20R

Бренд: ADTRAN Страницы: 9

Бренд: ForeScout Страницы: 28

Бренд: NETGEAR Страницы: 169

OCTOPUS 5TX-EEC

Бренд: Hirschmann Страницы: 6

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

18x18 Card Cage

Бренд: WolfPack Страницы: 31

Бренд: Paradyne Страницы: 6

MMAC-Plus 9G536-04

Бренд: Cabletron Systems Страницы: 42

Бренд: ADIC Страницы: 140

Бренд: Xantech Страницы: 6

Бренд: C&H Technologies Страницы: 50

Бренд: qpcom Страницы: 4

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 8

AirProtect Enterprise Engine 6100

Бренд: 3Com Страницы: 12

Бренд: 2Wire Страницы: 20

Бренд: 3Com Страницы: 82

Бренд: Cambium Networks Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды