background image

EC Declaration of Conformity

NOTE

:  This  De cla ra tion  of  Con for mi ty  and  the 

-mark af fixed to the na me plate are va lid for the va cuum pump wi thin the Busch-scope of de li ve ry. 

When this va cuum pump is in te gra ted into a lar ger ma chi ne ry the ma nu fac tu rer of the lar ger ma chi ne ry (this can be ope ra tor, too) must conduct the 
confor mi ty as sess ment pro cess for the lar ger ma chine, issue the De cla ra tion of Con for mi ty for it and affix the 

-mark.

We

Ate liers Busch S.A.
Zone Indus trielle
2906  Che ve nez
Swit zer land

re pre sen ted in the Eu ro pean Union by  

Dr.-Ing. K. Busch GmbH
Schauins landstr.  1
79689 Maul burg
Ger ma ny

de clare that the va cuum pumps 

R 5 0160 D / R 5 0202 D / R 5 0250 D / R 5 0302 D

in  ac cor dance  with  the  Eu ro pean  Di rec ti ves 

“Ma chi ne ry”  98/37/CE,

“Elec tri cal Equip ment De si gned for Use wi thin Cer tain Vol tage Li mits” (so cal led “Low Vol tage”) 73/23/EEC,

“Elec tro ma gne tic  Com pa ti bi li ty”  89/336/EEC

have  been  de si gned  and  ma nu fac tu red  to  the  fol lo wing  spe ci fi ca tions:

Stan dards

Title of the stan dard

Har mo ni sed  stan dards

EN ISO 12100-1
EN ISO 12100-2

Sa fe ty of ma chi ne ry - Ba sic concepts, ge ne ral prin ci ples of de sign - Part 1 and 2

EN 294

Sa fe ty of ma chi ne ry - Sa fe ty dis tance to pre vent dan ger zo nes being rea ched by the up per limbs

EN 1012-1
EN 1012-2

Com pres sors and va cuum pumps - Sa fe ty re qui re ments - Part 1 and 2

EN 60204-1

Elec tri cal equip ment of ma chi nes - Part 1:

EN 61000-6-1
EN 61000-6-2

Elec tro ma gne tic  com pa ti bi li ty  (EMC)  -  Ge ne ric  im mu ni ty  stan dards;  Part  1  and  2

EN 61000-6-3
EN 61000-6-4

Elec tro ma gne tic  com pa ti bi li ty  (EMC)  -  Ge ne ric  emis sion  stan dards;  Part  1  and  2

Na tio nal  stan dards

EN ISO 2151

Acous tics - Noise test code for com pres sors and va cuum pumps - Engi nee ring me thod (grade 2)

Ma nu fac tu rer

Man da to ry  wi thin  the  EC:

Ro man  Heil

Ge ne ral  di rec tor 

Dr.-Ing. Karl Busch

Ge ne ral  di rec tor

Содержание R50160D


























Отзывы: