background image

 

2.

 

UNPACKING THE APPLIANCE 

2.1

 

Carefully examine the carton for damage before unpacking. If it is obviously damaged, consult 
the supplier as to whether to proceed with the installation. 

2.2

 

Make sure the carton is stood upright and open the top. Remove the cardboard top fitting and 
place to one side; this box can be used as a hearth protector when installing the fire. 

2.3

 

Remove  the  fittings  boxes  contained  within,  open  them  and  check  the  condition  of  the 
contents. Remove the fire and examine its general condition, paying particular attention to the 
frame, the glass front and fire box flanges. 

2.4

 

If satisfied by the general condition, place the decorative components to one side and proceed 
with the installation. If in any doubt, seek advice from the supplier. 

 

Read these instructions fully before proceeding even if you have fitted this model before. 

2.5

 

Component Checklist: 

1 x firebox complete with burner controls assembly with glass panel fitted 

 

1 x remote control hand set   

 

1 x outlet grille 

 

1 x ceramic log set (comprising large rear log, large front log and two intermediate logs) 

 

1 x installation fitting kit, included surround fixing screws 

1 x decorative trim assembly if required (in separate box) 

3.

 

GENERAL NOTES & REQUIREMENTS 

3.1

 

Gas appliances must be installed in accordance with the rules in force. In the UK it is the law 
that all gas appliances must be installed by a Gas Safe ™ registered installer (formerly CORGI), 
in  accordance  with  the  Gas  Safety  (Installation  and  Use)  Regulations  (as  amended).  The 
installation  must  also  be  in  accordance  with  the  relevant  parts  of  local  and  national  building 
regulations. 

Failure to have the fire fitted by a qualified person nullifies ALL guarantees.

 

3.2

 

All parts of this appliance are considered to be working surfaces. This includes the convection 
grille outlet. 

3.3

 

This  appliance  must  not  be  installed  or  used  in  a  living  room  of  less  than  50  m³  in  volume  & 
must have a minimum purpose provided permanent ventilation of 100 cm

2

.  

3.4

 

Adjoining spaces, not separated by a door may be included. To convert cubic feet (ft³) to cubic 
metre (m³) divide the room volume in cubic feet by 35.3.

 

3.5

 

When providing ventilator openings consideration must be given to the avoidance of locations 
where  discomfort  from  draughts  may  cause  the  user  to  block  the  openings.  Similarly  the 
possibility of curtains or furniture blocking ventilation openings must be considered.

  

 

The air vent must be at least 1 metre away from the appliance. Floor vents, window vents or 
chimneys are not suitable means of ventilation.    

This appliance shall not be installed or used in any of the following: 

 

high rise blocks of flats 

 

basements  

 

bedroom / bathrooms  

 

in corridors, stairways, landing, or hallways of multi occupancy dwellings 

 

garages or rooms containing petroleum products.  

Additionally,  the  appliance  must  not  be  used  in  rooms  where  the  atmosphere  is  likely  to 
contain water or chemical vapours which may adversely affect the appliance or its finish. 

3.6

 

Soft furnishings, decorations and loose wall coverings etc. must not be placed within 1 metre 
of the appliance and its convection outlets (see 5.0). Be aware of curtains etc. which could be 
blown towards the appliance.

  

 

Содержание ASTUTE G4113





























Отзывы: