Buhler SCS 104 Скачать руководство пользователя страница 3

Страница: 3 / 75

SCS 104

Contents

Introduction..................................................................................................................................................................................................................... 3
1.1

Intended Use......................................................................................................................................................................................................... 3

1.2

System Description ............................................................................................................................................................................................. 3
1.2.1

Sample conditioning section ............................................................................................................................................................ 3

1.2.2

Calibration gas section ....................................................................................................................................................................... 3

1.2.3

Blowback air section ............................................................................................................................................................................ 3

1.2.4

Manual control..................................................................................................................................................................................... 4

1.2.5

External control and monitoring.................................................................................................................................................... 4

1.3

Scope of delivery .................................................................................................................................................................................................. 4

Safety instructions......................................................................................................................................................................................................... 5
2.1

Important advice ................................................................................................................................................................................................. 5

2.2

General hazard warnings ................................................................................................................................................................................. 6

Transport and storage .................................................................................................................................................................................................. 7

Installation and connection ........................................................................................................................................................................................ 8
4.1

Installation site requirements......................................................................................................................................................................... 8

4.2

Gas Line Connections ......................................................................................................................................................................................... 8

4.3

Electrical connections ........................................................................................................................................................................................ 8

Operation and control ................................................................................................................................................................................................ 10
5.1

Start up................................................................................................................................................................................................................. 10

5.2

Using the device menu .................................................................................................................................................................................... 10
5.2.1

Use of menu functions...................................................................................................................................................................... 10

5.2.2

Lock Menu.............................................................................................................................................................................................. 11

5.2.3

Overview of the menu items............................................................................................................................................................ 11

5.2.4

Description of menu functions ...................................................................................................................................................... 13

5.3

Manual operation of the SCS (front panel module CM0191)................................................................................................................ 16

5.4

Monitoring system operation on the controller module (front panel module CM0191) ............................................................. 16

5.5

External control ................................................................................................................................................................................................. 16

5.6

External monitoring ......................................................................................................................................................................................... 16

5.7

Flow Meter Operation....................................................................................................................................................................................... 17

5.8

Pressure regulators and gauges .................................................................................................................................................................... 17

Maintenance.................................................................................................................................................................................................................. 18

Service and repair......................................................................................................................................................................................................... 19
7.1

Troubleshooting ................................................................................................................................................................................................ 19
7.1.1

Error messages on the display ....................................................................................................................................................... 20

7.2

Safety instructions ............................................................................................................................................................................................ 21

7.3

Replacing the Fuse in the Front Panel......................................................................................................................................................... 22

7.4

Replacing the fuse (F1) from the gaspumps .............................................................................................................................................. 22

7.5

Replacing the fuse (F2) from the peristaltic pumps................................................................................................................................ 22

7.6

Replacing the Peristaltic Pump Hose........................................................................................................................................................... 22

7.7

Replacing the filter element........................................................................................................................................................................... 23

7.8

Replace Flowmeter module............................................................................................................................................................................ 23

7.9

Install Extension module gaspump ............................................................................................................................................................. 23

7.10 Drying the Moisture Detector........................................................................................................................................................................ 24
7.11

Calibration of the moisture detector........................................................................................................................................................... 24

7.12 Spare parts and accessories ........................................................................................................................................................................... 24

7.12.1

Spare parts and accessories............................................................................................................................................................ 24

Disposal ........................................................................................................................................................................................................................... 25

Appendices..................................................................................................................................................................................................................... 26
9.1

Technical Data.................................................................................................................................................................................................... 26

9.2

Legend................................................................................................................................................................................................................... 27

9.3

Drawing 1: Flow chart....................................................................................................................................................................................... 28

9.4

Drawing 2: Wiring diagrams ......................................................................................................................................................................... 29

9.5

Drawing 3: Front view...................................................................................................................................................................................... 30

Bühler Technologies GmbH

BECS0031 ◦ 02/2020

Содержание SCS 104












































































Результаты поиска

Содержание SCS 104

Отзывы:

Похожие инструкции для SCS 104

Бренды по названию

Популярные бренды

Buhler SCS 104, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SCS 104

Отзывы:

Похожие инструкции для SCS 104

Бренды по названию

Популярные бренды