manualshive.com logo in svg

Buhler SCS 104, Инструкция по установке и эксплуатации

"Руководство по установке и эксплуатации Buhler SCS 104 доступно для бесплатного скачивания на manualshive.com. Эта инструкция содержит всю необходимую информацию для правильной установки и использования продукта. Скачайте руководство сейчас, чтобы насладиться всеми преимуществами этого устройства."

Поделиться
Скачать
background image

CPsingle, CPdouble

Contents

1

Introduction.....................................................................................................................................................................................................................  2
1.1

Intended use .........................................................................................................................................................................................................  2

1.2

Scope of delivery ..................................................................................................................................................................................................  2

1.3

Type plate ..............................................................................................................................................................................................................  2

1.4

Peristaltic pump ordering information........................................................................................................................................................  3

2

Safety instructions.........................................................................................................................................................................................................  4
2.1

Important advice ................................................................................................................................................................................................. 4

2.2

General hazard warnings ................................................................................................................................................................................. 4

3

Transport and storage .................................................................................................................................................................................................. 6

4 Installation and connection ........................................................................................................................................................................................  7

4.1

Installation site requirements.........................................................................................................................................................................  7

4.2

Mounting...............................................................................................................................................................................................................  7
4.2.1

Installing the built-in style ...............................................................................................................................................................  8

4.3

Electrical connections ........................................................................................................................................................................................ 9
4.3.1

Electrical Connections (housing version / 115 V or 230 V) ........................................................................................................  9

4.3.2

Electrical Connections (built-in version / 115 V or 230 V) .........................................................................................................  9

4.3.3

24 V DC....................................................................................................................................................................................................  9

5

Operation and control ................................................................................................................................................................................................  10

6 Maintenance...................................................................................................................................................................................................................  11

7

Service and repair.......................................................................................................................................................................................................... 12
7.1

Safety instructions ............................................................................................................................................................................................  12

7.2

Replacing the hose ............................................................................................................................................................................................. 13

7.3

Spare parts and accessories ............................................................................................................................................................................ 13
7.3.1

Ordering information replacement hoses for 0.3 l/h pumps ...............................................................................................  13

8 Disposal ...........................................................................................................................................................................................................................  14

9 Appendices...................................................................................................................................................................................................................... 15

9.1

Technical data ..................................................................................................................................................................................................... 15

9.2

Dimensions 115 / 230 V.....................................................................................................................................................................................  16

9.3

Dimensions 24 V ................................................................................................................................................................................................. 17

10 Attached documents ...................................................................................................................................................................................................  18

i

Bühler Technologies GmbH

BE450021 ◦ 01/2017

Содержание SCS 104












































































Отзывы:

Нет отзывов

Похожие инструкции для SCS 104

M3S Triton Description Handbook preview
Triton
Бренд: M3S Страницы: 40
Balluff BML SL1-ALZ-ZZ Series Condensed Manual preview
BML SL1-ALZ-ZZ Series
Бренд: Balluff Страницы: 26
Hanna Instruments HI99151 Quick Reference Manual preview
HI99151
Бренд: Hanna Instruments Страницы: 2
Hanna Instruments HI736 Instruction Manual preview
HI736
Бренд: Hanna Instruments Страницы: 2
Hanna Instruments HI 991401 Instruction Manual preview
HI 991401
Бренд: Hanna Instruments Страницы: 2
Hanna Instruments HI 98140 Manual preview
HI 98140
Бренд: Hanna Instruments Страницы: 4
Hanna Instruments HI 8314 Instruction Manual preview
HI 8314
Бренд: Hanna Instruments Страницы: 2
Varian CP-4900 Micro-GC Firmware Update Manual preview
CP-4900 Micro-GC
Бренд: Varian Страницы: 13
Nidec FG-3000R Series Operation Manual preview
FG-3000R Series
Бренд: Nidec Страницы: 8
Jaquet T411 Operating Instructions Manual preview
T411
Бренд: Jaquet Страницы: 27
Ecodhome 01335-1800-00 Installation Manual preview
01335-1800-00
Бренд: Ecodhome Страницы: 12
Milkotester MASTER Touch Operating Instructions Manual preview
MASTER Touch
Бренд: Milkotester Страницы: 44
E+E Elektronik HUMIPORT 10 Manual preview
HUMIPORT 10
Бренд: E+E Elektronik Страницы: 48
Reed Instruments 800837000736 Instruction Manual preview
800837000736
Бренд: Reed Instruments Страницы: 12
Ega Master MASTERVISION ECO Operating Instructions Manual preview
MASTERVISION ECO
Бренд: Ega Master Страницы: 48
R.M. Young 05305L Instructions Manual preview
05305L
Бренд: R.M. Young Страницы: 11
M-system 48NAV Instruction Manual preview
48NAV
Бренд: M-system Страницы: 8
GREISINGER GMH 3161-13 User Manual preview
GMH 3161-13
Бренд: GREISINGER Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды