Buhler SCS 104 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 75

background image

SCS 104

CAUTION

Supply cable

The power adapter must be suitable for the maximum power input of the device. It must
be heat-resistant and must not come into contact with hot surfaces. The power adapter
must meet IEC60227 or IEC60245. Or be approved by another recognised testing body.

Run the lines so the insulation will not be damaged. If necessary, secure the lines with suitable means and avoid excess line
lengths.

The power and voltage supply must be equipped with ELCB.

The ELCB (tripping current 30 mA) must shut off the load within the specified period (200 ms at 115 VAC, 40 ms at 230 VAC). It
must be suitable for the maximum load.

9

Bühler Technologies GmbH

BECS0031 ◦ 02/2020

«
...
9
10
11
12
13
...
»

Содержание SCS 104












































































Отзывы:

Нет отзывов

Похожие инструкции для SCS 104

Бренд: Keithley Страницы: 148

Бренд: Nady Audio Страницы: 2

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 4

Бренд: Velleman Страницы: 8

Бренд: velocomp Страницы: 4

Бренд: WAGNER Страницы: 9

Бренд: Magnet-physik Страницы: 32

Бренд: Vaisala Страницы: 40

Бренд: ProsKit Страницы: 10

Бренд: TQC Sheen Страницы: 16

Бренд: OHAUS Страницы: 6

Бренд: East Tester Страницы: 27

Бренд: General Страницы: 12

3501B1260KG/M010LN

Бренд: PCB Piezotronics Страницы: 10

Бренд: Zhengzhou Minghe Electronic Technology Страницы: 7

Бренд: Campbell Страницы: 37

Solar Auxiliary Power Unit

Бренд: J-TECH Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды