Buffalo TeraStation 6000 Series Скачать руководство пользователя страница 220

Страница: 220 / 226

Close the front cover.

LCD Panel

The LCD panel can be cycled through different modes by pressing the display button on the front of the TeraStation.

Modes

LCD Message

Description

Corrective Action

LAN

Note:

The “x”

indicates the
number of the
LAN port where
the Ethernet cable
is connected.

LAN

Not Connected

Not connected to a network.

Connect an Ethernet
cable to the LAN
port.

LAN

Half Duplex

10 Mbps

Connected at 10 Mbps half duplex.

LAN

Full Duplex

10 Mbps

Connected at 10 Mbps full duplex.

LAN

Half Duplex

100 Mbps

Connected at 100 Mbps half duplex.

LAN

Full Duplex

100 Mbps

Connected at 100 Mbps full duplex.

LAN

1000 Mbps

Connected at 1000 Mbps.

LAN

2.5 Gbps

Connected at 2.5 Gbps.

LAN

5 Gbps

Connected at 5 Gbps.

LAN

10 Gbps

Connected at 10 Gbps.

LAN

Port Trunking

Displays if port trunking is configured.

Model Name/
Firmware Version

TS6400D
FW Version 1.00

Displays the model name and firmware
version of your model.

Note:

This example is using a TS6400DN unit.

The numbers and letters after “TS” may vary
depending on your model.

Hostname

Hostname:
TS6400D

xxx

Displays the hostname.

Note:

The “xxx” is assigned using the last

three-digits of MAC address.

219

Chapter 10 Appendix

Содержание TeraStation 6000 Series



































































































































































































































Результаты поиска

Содержание TeraStation 6000 Series

Отзывы:

Похожие инструкции для TeraStation 6000 Series

Бренды по названию

Популярные бренды

Buffalo TeraStation 6000 Series, Руководство пользователя

Результаты поиска

Содержание TeraStation 6000 Series

Отзывы:

Похожие инструкции для TeraStation 6000 Series

Бренды по названию

Популярные бренды